JTEKT Corporation
Torrington NEEDLE BEARING INNER RACES TOR IR-081212
Koyo IR-081212 Inch Series Inner Ring, 1/2 in ID x 3/4 in OD, 3/4 in OAW, For Use With HJ-122012 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-101412
Koyo IR-101412 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 3/4 in OAW, For Use With HJ-142212 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-192420
Koyo IR-192420 Inch Series Inner Ring, 1-3/16 in ID x 1-1/2 in OD, 1-1/4 in OAW, For Use With HJ-243320 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-2020
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARING INNER RACES TOR IR-2424
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARING INNER RACES TOR IR-242820
Koyo IR-242820 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1-1/4 in OAW, For Use With HJ-283720 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-88
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARINGS TOR JT-129
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway to the rollers. The small cross-section of the drawn cup bearing provides high load-carrying capability with minimum required space, drawn cup bearings are easily installed with a press fit in the housing.
Torrington NEEDLE BEARINGS TOR JTT-1012
Koyo JTT-1012 Inch Series Caged Open Ends Drawn Cup Needle Roller Bearing, 5/8 in Dia Bore, 13/16 in OD, 3/4 in W, 1980 lbf Dynamic/2910 lbf Static Load
Torrington THRUST BEARING WASHERS TOR TRA-1018
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRA-1828
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRB-2435
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRC-2233
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRC-2435
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST NEEDLE BEARING WASHERS TOR TRD-2435
Koyo TRD-2435 Thrust Washer, 38.1 mm ID x 55.55 mm OD, 3.2 mm W
Torrington THRUST NEEDLE BEARINGS TOR AXK-3552
Thrust needle roller and cage assemblies are complements of small diameter needle rollers, arranged in a spoke-like configuration. Needle rollers are equally spaced by means of a cage, its web section separates the rollers and provides guidance to keep them tracking in an orbital path. The purpose of these assemblies is to transmit a thrust load between two relatively rotating objects while greatly reducing friction. Thrust needle roller and cage assemblies also can be unitized with lipped washers to serve as raceway surfaces for the needle rollers. Washers can be supplied separately or can be mechanically unitized to the thrust needle roller and cage assemblies for ease of handling.
Recently Viewed
Gates® Power Transmission PowerGrip® GT®2 Twin Power® TP2000-8MGT-30 9232 Synchronous Belt, 250 Teeth, 8 mm Pitch, 2000 mm OAL, 30 mm W, Neoprene
PowerGripâ„¢ GTâ„¢2 Twin Powerâ„¢ Belts feature dual-sided teeth to provide equal load carrying capacity on either belt surface, enabling synchronization from both driving surfaces. These synchronous belts ensure high loading capacity on contra-rotating drives and ensure smooth running and high flexibility. Gates Twin Power PowerGrip GT2 belts are designed to perform at high speeds and characterized by low-running noise, with a larger tooth profile for increased performance capacity.
40-TOOTH #50-1 CHAIN SPROCKETS IDC 50-B-40-F-1-1/2
40 TOOTH SPROCKETS FOR #50 CHAIN
50-B-11-F-5/8 11 Tooth Sprockets For #50
11 TOOTH SPROCKETS FOR #50 CHAIN-IDC50B11F5/8 >
50-B-12-F-5/8 12-t Finished-bore Sprockets For #50 Chain
12-T FINISHED-BORE SPROCKETS FOR #50 CHAIN -IDC50B12F5/8 >
DOUBLE SHIELDED BALL BEARING WITH SNAP RING-GUL63012ZNR >
50-B-36-F-1-3/4 36 Tooth Sprockets For #50
36 TOOTH SPROCKETS FOR #50 CHAIN-IDC50B36F13/4 >
