Koyo TRA-1828 Double Direction Thrust Washer, 28.58 mm ID x 44.45 mm OD, 0.81 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
-
BrandKoyo
-
UPC605790210181
-
Manufacturer Part NumberTRA-1828
-
CountryUSA
-
TypeDouble Direction
-
Width0.81 mm
-
Inside Diameter28.58 mm
-
Outside Diameter44.45 mm
-
Suitable For Use WithNTA Series Needle Roller Bearing and Cage Assembly
- Dimensions for bore and OD of thrust assemblies and washers are nominal
- Thrust washers burnished at least one quarter of bore area (remainder is rough breakaway finish)
- OD finish of washers will be as blanked
-
UNSPSC31161814
-
Catalog
Recently Viewed
Koyo TRA-1828 Double Direction Thrust Washer, 28.58 mm ID x 44.45 mm OD, 0.81 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Crosby® 1032091 HG-227-3/4 X 12 Turnbuckle, Jaw/Eye, 3/4 in Thread, 5200 lb Working, 12 in Take Up, 24.49 in L Close, Steel
Crosby® 1032091 HG-227 Turnbuckle, Jaw/Eye, 3/4 in Thread, 5200 lb Working, 12 in Take Up, 24.49 in L Close, Steel
Crosby® 1031993 HG-227-5/8 x 6 Turnbuckle, Jaw/Eye, 5/8 in Thread, 3500 lb Working, 6 in Take Up, 16.27 in L Close, Steel
Crosby® 1031993 HG-227 Turnbuckle, Jaw/Eye, 5/8 in Thread, 3500 lb Working, 6 in Take Up, 16.27 in L Close, Steel
The Super Ball Bushing® bearing has been the industry standard for self-aligning linear bearings for over twenty years. This bearing provides three times the load capacity or 27 times the travel life of conventional linear bearings. Besides the dramatic increase in load capacity, the Super Ball Bushing® bearing is self-aligning, lightweight and adjustable with a low coefficient of friction. It is a quick and easy replacement for high friction plain bearings. The wear-resistant, engineered-polymer retainers and outer sleeves reduce inertia and noise in critical, high speed applications.
IKO BAM2220 Inch Series Caged Shell Needle Roller Bearing, 1-3/8 in Dia Bore, 1-5/8 in OD, 1 Row, 1-1/4 in W, 28900 N Dynamic/67100 N Static Load
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
Koyo BH-1624 Inch Series Open Ends Uncaged Drawn Cup Needle Roller Bearing, 1 in Dia Bore, 1-5/16 in OD, 1-1/2 in W, 12030 lbf Dynamic/25900 lbf Static Load
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
