L.S. Starrett
Starrett® 56A 56 Series Small Surface Gage
Starrett Surface Gages are designed for a wide variety of uses. This is a basic tool for machinists and toolmakers. The main uses are for accurately scribing lines, transferring measurements and for probing surfaces in inspection work. 4" Spindle, 2" x 1 1/2" Base.
Starrett® 567, 7 Pieces, 1-5/16 in Capacity
V-Blocks come in a variety of styles to suit the numerous requirements of machinists. Used for general shop use and layout work, as well as for holding stock in place during light-duty milling, drilling, and grinding operations. All clamp screws have a hole to help secure the workpiece.
Starrett® 565G Drive Pin Punch, 1/4 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 6mm (1/4") Diameter.
Starrett® 565F Drive Pin Punch, 7/32 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 5.5mm (7/32") Diameter.
Starrett® 565E Drive Pin Punch, 3/16 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 5mm (3/16") Diameter.
Starrett® 565C Drive Pin Punch, 1/8 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 3mm (1/8") Diameter.
Starrett® 565B Drive Pin Punch, 3/32 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 2.5mm (3/32") Diameter.
Starrett® 565A Drive Pin Punch, 1/16 in Steel Tip, 4 in OAL
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 1.5mm (1/16") Diameter.
Starrett® 505P-7 Global Series® Combination Dial Reading Miter Protractor, 0 to 360 deg Measuring, 7 in L, Plastic
The 175mm (7") Plastic Miter Protractor takes error-prone calculations out of the process of miter cuts. Tool is ideal for carpenters, plumbers and all building trades that require the measuring and transferring of angles and invaluable for home use.
Starrett® 491-12-4R Reversible Bevel Protractor, 0 to 180 deg Measuring, 7 in L, 12 in L x 1 in W x 3/32 in THK Blade, Graduations 4R - 8ths, 16ths, Quick-Reading, 32nds, 64ths, Cast Iron
Starrett® bevel protractors have revolving turrets with direct reading double graduations a full 0 - 180 deg in opposite directions. This permits direct reading of angles above or below the blade. Equipped with a handy spirit level.
Starrett® 467M Thickness Gage, 0.04 to 5 mm, Tempered Steel
The Starrett Metric Thickness Gage is used in automotive, aviation, diesel and farm equipment manufacture and service and also in jig, fixture, gage and experimental work. Especially useful in adjusting tappets, spark plugs, distributor points, checking bearing clearances and gear play, fitting pistons, rings and pins and gaging narrow slots. Made in a wide range of types and sizes, each having from 6 up to 26 leaves ranging in thickness from .0015-.200" and 0.03-5mm thick straight or tapered. Thickness Gage, .0.04-5.0mm Range, 13 Leaves.
Starrett® 449BZ-6R Mechanical Depth Micrometer With Non-Rotating Blade, 0 to 6 in, Graduations: 0.001 in
The Starrett 449, 449M Series Micrometer Depth Gage with Non-Rotating Blade includes a .045" thick x 1/8" wide (1.2 x 3.2mm) blade that can be turned with the fingers and positioned at any angle relative to the base. In operation, the blade does not turn, but moves perpendicularly only, permitting depth measurement of narrow shoulders without the blade rolling off. This is also ideal for slots and recesses as narrow as .045" (1.2mm). Furnished with a 2-1/2" (63mm) or a 4" (100mm) base. 0-6" Range, .001" Grad, 4" Base, 6 Rods, in Case.
Starrett® 387-18 Beveled Straight Edge, Imperial Measuring System, Graduations 32nds of an Inch, Steel, Regular Steel
The Starrett 387 Series Steel Straight Edge with Bevel and Graduated End is precision ground and nicely finished to rigid Starrett standards. It is unexcelled for drawing or scribing straight lines and checking surfaces for straightness. Its thickness and design permits it to retain its shape and accuracy, but still be portable and easy to handle. 18" (450mm).
Starrett® 3810A Global Series® Digital Portable Electronic Hardness Tester, Leeb Scale, 200 HL Min, 960 HL Max Hardness, +/-0.5 % Accuracy, Battery
The 3810A is a state-of-the-art digital instrument designed to test the hardness of large hard metal parts. Loaded with useful functions such as USB output and a built in printer, the 3810A is an ideal choice for fast accurate hardness testing. This versatile tester can perform tests that easily convert to the most popular hardness scales, including Rockwell, Brinell, Vickers and Shore. The tester is easy to use. Simply load the impact body, place the impact body on your test piece, then push the button to begin testing. The 3810A is designed to test large hard parts. For example, tool steel should be close to 1" thick of solid material. The 3810A comes with a D impact device, calibration block, cleaning brush, manual and a carrying case.
Starrett® 3805D Electronic Durometer, 0 to 100 Measuring
The 3805D is used to measure the hardness of Rubber, Hard Plastics: Harder grades such as rigid thermoplastics, plexiglass, thermoploystrene, vinyl, sheet, cellulode acetate, thermosetting, Laminates (ie fornica), Other: Paper filled calendar rolls, calendar bowls, etc. (materials that would not normally indent under fingernail pressure, such as a pocket comb or bowling ball). Note: These units are not designed to ASTM specifications and cannot be certified as such.
Starrett® 284 Acme Standard Screw Thread Gage, 1 to 10 TPI Measuring, Steel, Black Penetrate
The Starrett 284 Acme Standard Screw Thread Gage is a standard for grinding and setting tools when cutting Acme threads, which have the same depth as square threads but the sides of the threads are at an inclination of 14-1/2 Deg (29 Deg included angle). This form of thread is used extensively and has in many instances replaced the square thread in machine construction. The advantages of the Acme thread is its strength and the ease by which it can be cut compared with square threads.
Starrett® 25R Shockproof Contact Point Set, For Use With AGD Dial Indicator, High Grade Steel
The Starrett Contact Point Set includes: 14 points with #4-48 screw thread to fit AGD indicators; a regular 1/4" (6.3mm) long point; 9 special form points; a 28 shock absorbing anvil; and 3 extra long points 1/2", 3/4" and 1" (13, 19, 25mm) long. The set features high grade steel, hardened and ground. All points are mounted on a convenient aluminum ring for safe keeping and easy selection. Contact Point SET.
Starrett® 257A Full Sized Surface Gage
Starrett Surface Gages are designed for a wide variety of uses. This is a basic tool for machinists and toolmakers. The main uses are for accurately scribing lines, transferring measurements and for probing surfaces in inspection work. 9" Spindle.
Starrett® 25-441J 25 Series AGD Group 2 Continuous Dial Indicator, 1 in, 0 to 100 Dial Reading, 0.001 in, 2-1/4 in Dial
Starrett® 25-441J 25 Series AGD Group 2 Continuous Dial Indicator, 1 in, 0 to 100 Dial Reading, 0.001 in, 2-1/4 in Dial
Starrett® 248E 248 Extra Long Drive Pin Punch, 3/8 in, 8 in OAL, Steel
The Starrett 248 Drive Pin Punch is intended for machine shop and motor service work, extra long in size, measuring 200mm (8"), with 114mm (4-1/2") bodies and 89mm (3-1/2") drive pin section. 200mm (8") Length, 9.5mm (3/8") Diameter.
Starrett® 248D Extra Long Drive Pin Punch, 5/16 in, 8 in OAL, Steel
The Starrett 248 Drive Pin Punch is intended for machine shop and motor service work, extra long in size, measuring 200mm (8"), with 114mm (4-1/2") bodies and 89mm (3-1/2") drive pin section. 200mm (8") Length, 8mm (5/16") Diameter.
Starrett® 248C 248 Extra Long Drive Pin Punch, 1/4 in, 8 in OAL, Steel
The Starrett 248 Drive Pin Punch is intended for machine shop and motor service work, extra long in size, measuring 200mm (8"), with 114mm (4-1/2") bodies and 89mm (3-1/2") drive pin section. 200mm (8") Length, 6mm (1/4") Diameter.
Starrett® 248B 248 Extra Long Drive Pin Punch, 3/16 in, 8 in OAL, Steel
The Starrett 248 Drive Pin Punch is intended for machine shop and motor service work, extra long in size, measuring 200mm (8"), with 114mm (4-1/2") bodies and 89mm (3-1/2") drive pin section. 200mm (8") Length, 5mm (3/16") Diameter.
Starrett® 248A 248 Extra Long Drive Pin Punch, 1/8 in, 8 in OAL, Steel
The Starrett 248 Drive Pin Punch is intended for machine shop and motor service work, extra long in size, measuring 200mm (8"), with 114mm (4-1/2") bodies and 89mm (3-1/2") drive pin section. 200mm (8") Length, 3mm (1/8") Diameter.
Recently Viewed
Gates® Power Transmission Poly Chain® GT®2 14MX-112S-37 Synchronous Sprocket, 1-3/16 to 3-15/16 in Taper-Lock® Bore, 19.54 in OD, 112 Grooves, 19.65 in Dia Pitch, 2.06 in W Face
Poly Chain GT sprockets use the tooth profile designed and developed by Gates and function with Gates Poly Chain GT belts in all existing constructions. These sprockets are statically balanced to make sure the entire belt drive is as safe as possible. Furthermore, they are manufactured, specified, and tested to perfectly support the full power capabilities of the Gates Poly Chain belt product range. Belts and sprockets used together get the best out of your belt drive: maximum performance, prolonged antistatic properties and optimal lifetime.
Black Stallion® FS7-KHK-3XL FS7-KHK Flame Resistant Shirt, 3XL, Cotton, Khaki, Resists: Flame
Black Stallion FS7-KHK Flame-Resistant Cotton Work Shirt provides comfortable, reliable protection. The FS7-KHK is made of 7 oz. FR-treated cotton, giving it a generous comfortable fit. It also has chest pockets with flaps and durable metal snaps.
Lasco® 406-080 Elbow, 8 in Nominal, Slip End Style, SCH 40/STD, PVC, Nitrile Rubber Seal, Domestic
Lasco® 406-080 Elbow, 8 in Nominal, Slip End Style, SCH 40/STD, PVC, Nitrile Rubber Seal, Domestic
1-7/8"-ID INSERT BEARING-GENUC21030>
TPR-ID SPHERICAL ROLLER BEARING-GUL22212K >
3/4" -16" SAE RETHREAD HEX DIE-PDTER637260 >
