Dichtomatik 75102381 O-Ring, 912 Dash Number, 0.924 in ID x 1.156 in OD, FKM, 75 Shore A Durometer, Import, Custom 912-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102381
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter0.924 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter1.156 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75912
-
Instruction/Installation Manual
-
Specification Sheet
-
Catalog
Recently Viewed
Dichtomatik 75102381 O-Ring, 912 Dash Number, 0.924 in ID x 1.156 in OD, FKM, 75 Shore A Durometer, Import, Custom 912-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Gates® Power Transmission Tri-Power® AX94 Heavy Duty Molded Notch V-Belt, AX Section, 1/2 in W Top, 96 in L Outside, 5/16 in THK, EPDM
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
FLEXCOIL POLYURETHANE AIR HOSE ASSEMBLIES
I.D. X O.D.--5/16" X 15/32"
MPT FITTING--1/4" 2-RIGID
LENGTH--15'
COLOR--YELLOW
Dichtomatik 75102143 O-Ring, 221 Dash Number, 1.421 in ID x 1.699 in OD, FKM, 75 Shore A Durometer, Import, Custom 221-viton
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
FHP V-BELT 79."-JAS4L790 >
The Zamac Nailin® is a nail drive anchor which has a body formed from Zamac alloy. Drive nails are available in carbon or stainless steel. The anchor can be used in concrete, block, brick or stone. A corrosion-resistant Zamac alloy is used to form the anchor body with either a mushroom or flathead. The anchor can be used for light duty, tamperproof applications. The anchor is not recommended for overhead, life-safety or sustained tensile loading applications (see performance data section).
