Dichtomatik 75102143 O-Ring, 221 Dash Number, 1.421 in ID x 1.699 in OD, FKM, 75 Shore A Durometer, Import, Custom 221-viton
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102143
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter1.421 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter1.699 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75221
Recently Viewed
Dichtomatik 75102143 O-Ring, 221 Dash Number, 1.421 in ID x 1.699 in OD, FKM, 75 Shore A Durometer, Import, Custom 221-viton
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Our most popular 1/4” grinding wheel, the United Abrasives A24R is a great choice for long lasting, general purpose grinding. The A24R is composed of a special aluminum oxide grain which assures consistent stock removal for tough applications. United Abrasives/SAIT wheels are externally reinforced with fiberglass layers to provide ultimate safety. Proudly manufactured in the USA.
Drillco 72A104C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1/16 in Dia Cutter, 3/16 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 75A112C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 3/16 in Dia Cutter, 3/8 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Dichtomatik 75102159 O-Ring, 237 Dash Number, 3.359 in ID x 3.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 237-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 75A108C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 1/8 in Dia Cutter, 1/4 in Length of Cut, 4 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
