Dichtomatik 75102159 O-Ring, 237 Dash Number, 3.359 in ID x 3.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 237-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102159
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter3.359 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter3.637 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75237
Recently Viewed
Dichtomatik 75102159 O-Ring, 237 Dash Number, 3.359 in ID x 3.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 237-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 75A108C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 1/8 in Dia Cutter, 1/4 in Length of Cut, 4 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Dichtomatik 75102151 O-Ring, 229 Dash Number, 2.359 in ID x 2.637 in OD, FKM, 75 Shore A Durometer, Import, Custom 229-VITON
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 75A120C 7500 Center Cutting Double End Imperial Stub Length Finishing End Mill, 5/16 in Dia Cutter, 1/2 in Length of Cut, 4 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 735A116C 7350 Center Cutting Extra Long Length Imperial Single End Finishing End Mill, 1/4 in Dia Cutter, 1-1/2 in Length of Cut, 4 Flutes, 1/4 in Dia Shank, 4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Extra long
