Dichtomatik N70206 O-Ring, 206 Dash Number, 0.484 in ID x 0.762 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 206
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70206
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter0.484 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.762 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Dodge® 070393 Type S2000 Pillow Block Roller Bearing Unit, 4-7/16 in Dia Bore, 13 to 14 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 16-1/2 in OAL 9.63 in OAH
Dodge® 070393 Type S2000 Pillow Block Roller Bearing Unit, 4-7/16 in Dia Bore, 13 to 14 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 16-1/2 in OAL x 9.63 in OAH
Enerpac® RC-256 General Purpose Industry Standard Single Acting Hydraulic Cylinder, 25 ton Capacity, 6-1/4 in L Stroke, 10000 psi
Enerpac® hydraulic cylinders are available in hundreds of different configurations. Whatever the industrial application lifting, pushing, pulling, bending, holding, whatever the force capacity, stroke length, or size restrictions, single- or double-acting, solid or hollow plunger, you can be sure that Enerpac® has the cylinder to suit your high force application.
PROSTRAN GASOLINE PARTS CLEANING BRUSH - MAG11 >
Weiler® 03060 TL-6 Wide Face Wheel Brush, 6 in Dia Brush, 1-1/4 in W Face, 0.0118 in Dia Filament/Wire Crimped Filament/Wire, 2 in Arbor Hole
Weiler® 03060 TL-6 Wide Face Wheel Brush, 6 in Dia Brush, 1-1/4 in W Face, 0.0118 in Dia Filament/Wire Crimped Filament/Wire, 2 in Arbor Hole
Dichtomatik N70314 O-Ring, 314 Dash Number, 0.725 in ID x 1.147 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
