Gates AX59 Tri-Power® Industrial V-Belts - AX Section, 1/2 in Top Width, 1 Strand, 61.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
-
BrandGates® Power Transmission
-
UPC72053457193
-
Manufacturer Part NumberAX59
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness5/16 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialPolyester
-
ColorBlack
-
TypeHeavy Duty
-
Section SizeAX
-
Series9012
-
Number of Ribs1
-
Outside Length61 in
- Notches molded into the belt during manufacturing make this belt well suited for drives with smaller diameter sheaves
- Belt edge is machined for even sheave groove contact resulting in less slip and wear
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Patented EPDM Material construction provides -60 to 250 deg F temperature range to resist belt cracking
- Suitable for all industrial applications, particularly where small or sub-minimal sheave diameters are required
- Meets RMA oil and heat resistant standards
- Meets RMA static conductivity requirements
- Multi-duty recommended sheaves
- ARPM number: AX59
-
UNSPSC26101400
-
Standards/ApprovalsRMA Standard
-
Alternative Part Number90122059
-
Package DescriptionEACH
-
Catalog
Recently Viewed
Gates AX59 Tri-Power® Industrial V-Belts - AX Section, 1/2 in Top Width, 1 Strand, 61.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. The BMU bearings are commonly referred to as thrust bearings. These bearings have a 40 deg contact angle to accept heavy axial loads. The bearings have Universally Flush Ground rings to facilitate mounting in multiple bearing sets. The inner and outer rings have identical widths. These bearings can be mounted as DB, DF and DT pairs or can be combined into triplex and quadraplex sets. When two bearings are mounted together, a clearance or preload may be obtained without the use of shims or spacers. This bearing has a machined brass cage and is not available with seals or shields. These bearings are most commonly used in vertical pump and motor applications.
1.969" X 2.756" X .315" OIL SEALS
Dichtomatik 75115254 O-Ring, 244 Dash Number, 4.234 in ID x 4.512 in OD, PTFE, 55 Durometer, Import, Custom 244-TEFLON
O-rings are endless, ring shaped sealing elements with a circular cross-section that are manufactured from elastomer materials or PTFE. The designation of an O-ring is derived from the dimensions of its inner diameter and cord width in millimeters, along with the name of the material and its Shore A hardness.
SIZE-4 ARTIST BRUSHES-JWH972059>
Browning® 3750668 Taper Bore Bushing, 2-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
Browning® 3750668 Taper Bore Bushing, 2-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
