Gates® Power Transmission Hi-Power® II BB81 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 84 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
-
BrandGates® Power Transmission
-
UPC72053203615
-
Manufacturer Part NumberBB81
-
CountryUSA|Canada
-
Thickness17/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter5.73 in
-
Section SizeBB
-
Series9053
-
Number of Ribs1
-
Outside Length84 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
-
Alternative Part Number90530081
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Specification Sheet
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II BB81 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 84 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
Remke Tuff-Seal™ 7303-002R Closed Mesh Non-Insulated Single Weave Wide Range Strain Relief Grip With Galvanized Steel Mesh, 0.3 to 0.43 in Cable, For Use With 1/2 in NPT Connector, Aluminum
Tuff-Seal™ Wire Mesh Cable Grips distribute stress over a large area to prevent damage to wire, cable and flexible conduit. They are built to perform their task over an extended period of time without loosening their hold. All Remke wire mesh grips are available in a wide selection of cable ranges and eye styles where applicable and can be used in conjunction with any RSR cord connector.
JET® JLH Series Lever Hoists incorporate safety, durability and heavy duty construction for operation in severe industrial environments. Safety comes standard with features such as slip clutch style overload protection, which prevents the lever hoist from lifting or pulling damaging loads beyond its rated capacity. Our lightweight design, shorter handle and smaller body are ideal for confined areas and low headroom applications. Backed by a lifetime replacement warranty, JET® revolutionary single-piece brake design fuses the three components into the safest brake system in the market. The JET® JLH Series is available in 1/4 to 9 ton capacities, with standard lifts of 5 ft, 10 ft, 15 ft and 20 ft (custom lifts available). Whether it's inverted, vertical, horizontal or any other load angle, the JET® JLH Lever Hoist is the solution for your heavy duty industrial needs.
Weiler® 15071 Small Diameter Wheel Brush, 1 in Dia Brush, 3/16 in W Face, 0.006 in Dia Crimped Filament/Wire, 1/4 in Arbor Hole
Weiler® 15071 Small Diameter Wheel Brush, 1 in Dia Brush, 3/16 in W Face, 0.006 in Dia Crimped Filament/Wire, 1/4 in Arbor Hole
Magnolia Brush 176 Hand and Nail Brush, 4-3/4 in L x 1-1/4 in W Block, 5/8 in Tampico Trim
POLY-V V-BELT-JAS550J6>
