IKO LRT708035 Metric Series Inner Ring, 70 mm ID x 80 mm OD, 35 mm OAW, For Use With TAF809535 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Metric-type LRT series Inner Rings have shaft diameters from 5 to 440 mm.
-
BrandIKO
-
Manufacturer Part NumberLRT708035
-
CountryUSA
-
MaterialHigh Carbon Steel
-
Inside Diameter70 mm
-
Bore TypeTapered
- Without oil hole
-
UNSPSC31171547
-
Catalog
Recently Viewed
IKO LRT708035 Metric Series Inner Ring, 70 mm ID x 80 mm OD, 35 mm OAW, For Use With TAF809535 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Metric-type LRT series Inner Rings have shaft diameters from 5 to 440 mm.
MCR Safety WIN19 Winchester® Single Lens Safety Glasses, Anti-Scratch, Indoor/Outdoor Lens, Half-Frame Frame, Storm, Nylon Frame, Polycarbonate Lens, ANSI Z87.1-2010
MCR Safety WIN19 Winchester® Single Lens Safety Glasses, Anti-Scratch, Indoor/Outdoor Lens, Half-Frame Frame, Storm, Nylon Frame, Polycarbonate Lens, ANSI Z87.1-2010
18" GARAGE PUSH BROOM-JWH639672 >
Voltec 04-00102 3-Outlet In-Line Type STW GFCI Adapter With Lighted Power Block, 120 V, 12/3 AWG, 3 ft L
Voltec Power and Lighting has a full line of portable GFCI adapters, including right angle and in-line configurations, to fit every application. Choose from both 15 A u-ground and 20 A locking configurations. GFCI's protect the user from an electrical shock resulting from an unequal flow of electricity caused by current leakage. The occupational safety and health administration (OSHA) regulations state it is the employer's responsibility to provide GFCI's on all 120 V, 1-phase, 15/20 A receptacles on job sites that are not part of the permanent wiring of the structure.
1/2" X 5" CORRUGATED JOINT FASTENER-JWH723649 >
DRILLCO 1000N133 Imperial Silver and Deming Drill, 33/64 in Drill - Fraction, 0.5156 in Drill - Decimal Inch, 1/2 in Shank, HSS
Nitro® S&D drills offer superior performance over conventional HSS drills. All drills have 1/2" shanks, and 6" overall length. Their heavy-duty construction increases tool life and performance. 118° Split Point reduces walking at the drill point. 3-flats.
