Precision Deep Groove Ball Bearings
Nice® ER20 ER Series Non-Fill Slot Precision Deep Groove Ball Bearing With Extended Inner Ring, 1-1/4 in Dia Bore, 2.835 in OD, 1 Rows, 1-11/16 in W, 5755 lb Load
Gulf Bearing 7/16" DOUBLE-SHIELDED BALL BEARING GUL 1607-2-Z
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
Gulf Bearing 7/16" DOUBLE-SEALED BALL BEARINGS GUL 1620-2-RS
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
Gulf Bearing 3/8" DOUBLE-SHIELDED BALL BEARINGS GUL 1614-2-Z
Precision ground 1600® Series bearings are specially designed to provide a line of low cost yet high quality bearings for adaptation to a majority of precision bearing applications. They are made in easy to use inch dimensions and are recommended for medium loads and for maximum speeds in the range of 5000 rpm. The 1600® Series bearings are precision ground on all surfaces with exceptional care given to the ball grooves. Careful heat treatment provides a uniform and exact degree of hardness for maximum life. A ball retainer, or separator, is used to increase the range of allowable speeds by reducing ball-to-ball contact friction.
NSK is the World Leader in Deep Groove Ball Bearings. Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications, particularly those where high speeds and low power loss are required. NSK DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations.
Recently Viewed
Anvil® 0310088000 FIG 1125 Reducer, Coupling, 1-1/4 x 1/2 in Nominal, FNPT End Style, 150 lb, Malleable Iron, Black Oxide, Domestic
Anvil International offers the broadest line of malleable iron fitting sizes in both black and galvanized finishes. Every fitting is manufactured and tested to meet Anvil's strict quality standards. All Anvil Class 150 Malleable Iron Fittings conform to ASME B16.3 and unions conform to ASME B16.39. All elbows and tees 3/8 in (10 DN) and larger are 100% gas tested at a minimum of 100 PSI (6.9 bar).
7/8" X 30" TRUCK TIRE SPOON - KEN33239>
Precision machined tip provides exact fit for terminal block screws
1/8-Inch (3.2 mm) cabinet tip is up to 19-Percent stronger than competitors
Tip provides 76-Percent higher torque value than the required ASME B107 Standard
Cushion-Gripâ„¢ handle offers greater torque comfort
2-1/2" EMT CONDUIT SET SCREW COUPLING - APLTC517 >
MANUAL DRUM DEHEADER/OPENER - WES272018 >
