Gardner Bender GSW-18 Medium Duty Toggle Switch, 125 V AC/250 V DC, 8/4 A, 1/3 hp Power Rating, SPST Contact
The Gardner Bender 20/10 Amp Toggle Switch features an O ring and has screw terminals for quick-and-easy connections. The switch offers single-pole, single-throw (SPST) ON-OFF circuitry in a classic bat-handle design for easy usage.
-
BrandGardner Bender
-
UPC032076890186
-
Manufacturer Part NumberGSW-18
-
CountryUSA|Canada
-
Terminal TypeLead Wire
-
Power Rating1/3 hp
-
Closed Contact Resistance50 Ohm
-
ColorChrome
-
TypeMedium Duty
-
MountingSurface
-
Contact ConfigurationSPST
-
ActuatorLever
-
Voltage Rating125 V AC/250 V DC
-
Amperage Rating8/4 A
-
Number of Poles2
-
Dimensions1.47 in H
-
Environmental Conditions75 deg C Temperature
- 1/2 in mounting hole required
- ON/OFF (maintained)
- 6 in wire leads
- Toggle switch with a bat handle for easy operation
- 1/3 hp at 10 A/125 VAC
- Use for medium duty applications
- On-off SPST circuitry
- Compatible with standard 1/2 in mounting holes
- On-off faceplate for easy use
-
UNSPSC39122211
-
Standards/ApprovalsCSA Certified|UL Listed|RoHS Compliant|UL Recognized
-
Warranty1 Year
-
Specification Sheet
Recently Viewed
Gardner Bender GSW-18 Medium Duty Toggle Switch, 125 V AC/250 V DC, 8/4 A, 1/3 hp Power Rating, SPST Contact
The Gardner Bender 20/10 Amp Toggle Switch features an O ring and has screw terminals for quick-and-easy connections. The switch offers single-pole, single-throw (SPST) ON-OFF circuitry in a classic bat-handle design for easy usage.
The T6008 fiberglass multi-use twin 8 ft step ladder allows for 250 pounds on either side making these ladders ideal for two person jobs. The high performance dual holstertop has a paint and tool holder adding productivity to the job. Back up aluminum plates reinforce all top connectors and the TRACTION-TRED® steps are slip resistant. The PINCH-PROOF™ spreaders are externally located on the ladder and the EDGE® molded brace and foot pad combination provides enhanced bracing strength and increased protection against damage. Fiberglass rails are non-conductive for working near electricity.
IKO LRB141816 Inch Series Inner Ring With Oil Groove, 7/8 in ID x 1-1/8 in OD, 25.65 mm OAW, For Use With BR182616 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
Appleton® UNILETS™ T50A Type T Conduit Outlet Body, 1/2 in Hub, Form 85 Form, 4 cu-in Capacity, Pressure Cast Aluminum, Epoxy Powder Coated
Appleton® Form 85™ UNILETS™ Conduit Outlet Bodies, Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system, they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintece.
FAUCET AERATOR WASHERS WILL FIT MOST AERATOR-JWH413070 >
HellermannTyton T30R3C2 Standard Cable Tie, 5.8 in L x 0.14 in W x 1.1 mm THK, Polyamide 6.6, Orange
Engineered and manufactured for maximum performance and quality.
