Dixon® 30040104 Model 30 Thermometer, 50 to 500 deg F, 1 % Accuracy, 1/2 in MNPT Connection
Dixon® 30040104 Model 30 Thermometer, 50 to 500 deg F, 1 % Accuracy, 1/2 in MNPT Connection
-
BrandDixon®
-
UPC089109800285
-
Manufacturer Part Number30040104
-
CountryUSA
-
Temperature Rating50 to 500 deg F
-
Connection Type1/2 in MNPT
-
Accuracy1 %
-
SeriesModel 30
- For accurate temperature readings, immerse stem a minimum of 2 in, in agitated liquids or 4 in, in moving air or gas
- Temporary over or under range of 50 percent of scale up to 500 deg F will not affect the instrument accuracy
- Sturdy corrosion-resistant series 304 stainless steel case and bezel
- Optically clear crystal, strong glass, gasketed to maintain weather-tight integrity is standard
- 304 series stainless steel stem length, welded at tip and case connector to prevent leakage, 1/4 in dia is standard
- Hermetically sealed per ASME B40.3 external reset: slotted-hex adjustment head offers screwdriver or wrench use to field calibrate the thermometer
- Bi-metal element an extremely responsive temperature sensing helix which has been carefully sized and tested, heat treated and aged to relieve inherent stresses and insure continued accuracy
- Bi-metal helix dampening is coated with a viscous silicone to minimize pointer oscillation and to improve temperature transmission
- 4 in stem
- Warning: this product contains a chemical known to the state of California to cause birth defects or other reproductive harm
- Do not use in connection with drinking water
- Wash hands after handling
- 3 in face dial
-
UNSPSC41112200
-
Package Description1/BX
-
Standards/ApprovalsASME B40.3
-
WarrantyLimited
-
Catalog
Recently Viewed
Dixon® 30040104 Model 30 Thermometer, 50 to 500 deg F, 1 % Accuracy, 1/2 in MNPT Connection
Dixon® 30040104 Model 30 Thermometer, 50 to 500 deg F, 1 % Accuracy, 1/2 in MNPT Connection
Rex® 10412495 2000 Normal Duty Mounted Spherical Roller Bearing, 2-1/2 in Dia Bore, 5 in OD, 3-1/2 in W, 43240 lb Dynamic/53500 lb Static Load
Koyo TRC-2233 Double Direction Thrust Washer, 34.93 mm ID x 52.37 mm OD, 2.41 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Jones Stephens™ B91150 1-Piece Quarter-Turn Ball Valve, 1-1/2 in Nominal, Thread End Style, PVC Body, Standard Port, EPDM Softgoods
Jones Stephens™ B91150 1-Piece Quarter-Turn Ball Valve, 1-1/2 in Nominal, Thread End Style, PVC Body, Standard Port, EPDM Softgoods
1/4" DUOFAST STAPLES-JWH347798 >
MORSE® 10559 1314 General Purpose Taper Length Drill, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 5-3/8 in OAL, HSS, Black Oxide
MORSE® 10559 1314 General Purpose Taper Length Drill, 9/64 in Drill - Fraction, 0.1406 in Drill - Decimal Inch, 5-3/8 in OAL, HSS, Black Oxide
