Crown® by Aervoe® 7008Q Brite Galvanizing Compound, 1 qt Container, Bulk Liquid Form, 668 sq-ft/gal Coverage, 72 hr Curing
Crown's premium Brite Galvanize Coating 65% zinc Rich is a restorative coating fortified with zinc for preventing rust and corrosion on ferrous metal surfaces. Both aerosol and bulk use metallic zinc flake that is 97% pure. The bright zinc coating will restore galvanized steel to the bright look of hot dip with 65% zinc in the dry film which meets ASTM A780 standards.
-
BrandCrown® by Aervoe®
-
UPC088193270080
-
Manufacturer Part Number7008Q
-
CountryUSA
-
Temperature Rating50 to 90 deg F
-
Chemical CompositionHydrocarbon Propellant, Aliphatic Petroleum Distillates, Zinc Powder, Acetone, n-Butyl Acetate
-
FormBulk Liquid
-
VOC Content<500 g/L
-
Viscosity50 to 60 ku
-
Container Size1 qt
-
Container TypeCan
-
Coverage668 sq-ft/gal
-
Curing Time72 hr
-
Odor/ScentKetone
- A glistening coating with 65% pure zinc in dry film
- Stops rust and corrosion on any iron or steel surface for protection equal to or better than hot-dipped galvanizing
- Restores galvanized surfaces to the bright look of hot-dipped galvanizing
- Good film integrity after 500 hr salt spray (ASTM B-117)
-
UNSPSC31211507
-
Package Description4/CS
-
Standards/ApprovalsGHS Rev 04 (2011): US OSHA Compliant|CMA/ANSI Specified|Canadian WHMIS Standards|European Directives
-
Specification Sheet
-
SDS
Recently Viewed
Crown® by Aervoe® 7008Q Brite Galvanizing Compound, 1 qt Container, Bulk Liquid Form, 668 sq-ft/gal Coverage, 72 hr Curing
Crown's premium Brite Galvanize Coating 65% zinc Rich is a restorative coating fortified with zinc for preventing rust and corrosion on ferrous metal surfaces. Both aerosol and bulk use metallic zinc flake that is 97% pure. The bright zinc coating will restore galvanized steel to the bright look of hot dip with 65% zinc in the dry film which meets ASTM A780 standards.
1/4" X 36" HARDWOOD DOWEL ROD - JWH166732 >
1.250" X 2.374" X .313" RADIAL SHAFT DOUBLE LIP OIL SOLID SEALS
IKO BA2410ZOH Inch Series Caged Shell Standard Needle Roller Bearing With Oil Hole and Dust Cover, 1-1/2 in Dia Bore, 1-7/8 in OD, 1 Row, 5/8 in W, 17800 N Dynamic/27100 N Static Load
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
OBLONG PALMYRA SCRUB BRUSH - MAG171>
Browning® 1045459 VP Series Type 2 Variable Pitch Sheave, 1-1/8 in Finished Bore, 4-3/4 in OD, 1 Groove, 3.3 to 4.1 in (3L)/3.6 to 4.6 in (A/4L)/3.8 to 4.8 in (B/5L) Dia Pitch, 3/4 to 1-1/8 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
