Dichtomatik N70376 O-Ring, 376 Dash Number, 9.725 in ID x 10.145 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70376
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter9.725 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter10.145 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70376 O-Ring, 376 Dash Number, 9.725 in ID x 10.145 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
60 TOOTH SPROCKETS FOR #41 CHAIN-IDC41B60F1 >
FYH® SAA207 22FP7 SAA Cylindrical Ball Bearing Insert, 1-1/4 in Dia Bore, 2.83 in OD, 1.53 in W, 25.7 kN Dynamic/15.4 kN Static Load
FYH® SAA207 22FP7 SAA Cylindrical Ball Bearing Insert, 1-1/4 in Dia Bore, 2.83 in OD, 1.53 in W, 25.7 kN Dynamic/15.4 kN Static Load
Link-Belt® 10415869 200 Intermediate Duty Unmounted Ball Bearing Unit With Collar and Setscrews, 1-3/8 in Dia Bore, 2.8346 in OD, 1-17/32 in W, 5810 lb Dynamic/3440 lb Static Load
200 series intermediate duty ball bearing units provide a versatility of application arrangements for carrying shafts with radial or combination radial and thrust loads. They are designed for general purpose industrial machinery, conveyors, chain and belt drives, fans and blowers, power transmission and many other applications.
1/2-TON HAND CHAIN HOISTS-HRHCF00510>
Weiler® 08045 ST-4 Heavy-Duty Wheel Brush, 4 in Dia Brush, 1/2 in W Face, 0.014 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
Weiler® 08045 ST-4 Heavy-Duty Wheel Brush, 4 in Dia Brush, 1/2 in W Face, 0.014 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
