Dichtomatik S70351 O-Ring, 351 Dash Number, 4.725 in ID x 5.145 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberS70351
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialSilicone Rubber
-
ColorRed
-
Inside Diameter4.725 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter5.145 in
- Good chemical stability in water (up to 100 deg C), aliphatic engine and transmission oils, animal and plant based oils and greases
- Not resistant to fuels, aromatic mineral oils, water vapor (short periods up to a maximum of 120 deg C are possible), silicone oils and greases, along with acids and alkaline compounds
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|ISD Certified|NFPA Listed|PTDA Certified
-
Instruction/Installation Manual
-
Specification Sheet
-
Catalog
Recently Viewed
Dichtomatik S70351 O-Ring, 351 Dash Number, 4.725 in ID x 5.145 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
MORSE® 51137 5374 Standard Length Jobber Length Drill Bit, 31/64 in Drill - Fraction, 0.4844 in Drill - Decimal Inch, 118 deg Point, Solid Carbide, Bright
Dichtomatik N70407 O-Ring, 407 Dash Number, 2.225 in ID, Nitrile Rubber, 70 Shore A Durometer
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
OIL SEALS-NAT7781S>
Masterduct 363-100-107 Master-TPR PLUS Lightweight Suction and Transport Hose, 4 in Nominal, 25 ft L, Thermoplastic/Fabric/Steel
SUCTION AND TRANSPORT HOSE LIGHT/MEDIUM WEIGHT
Gates BX-100 Tri-Power® Industrial V-Belts - BX Section, 21/32 in Top Width, 1 Strand, 103.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
