Dichtomatik N70347 O-Ring, 347 Dash Number, 4.225 in ID x 4.645 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70347
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter4.225 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter4.645 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70347 O-Ring, 347 Dash Number, 4.225 in ID x 4.645 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Gates BX70 Tri-Power® Industrial V-Belts - BX Section, 21/32 in Top Width, 1 Strand, 73.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
FOAM PLASTIC WHITE NYLON SIDEWALL BRUSH - MAG6NP >
WOOD-HANDLE STEEL WIRE WHITE SIDEWALL BRUSH - MAG6S >
The United Abrasives/SAIT C24N Concrete wheel is excellent for grinding masonry, concrete, stone and aggregate. The C24N wheel can be used on hard to grind metal like cast iron and carbide. This wheel features a soft bond for fast stock removal. Proudly manufactured in the USA. Our unique Super-Lock™ Hub combines both a mechanical locking system and chemical bond providing one of the safest, vibration-free designs in the industry.
RIDGID® 32840 Heavy Duty Pipe Cutter, 2 to 4 in Nominal, Ergonomic Grip Handle
Make fast, clean cuts on ssteel pipes 2 to 4-inches in diameter. The Model 4-S single-wheel heavy-duty pipe cutter features an extra-long shank that protects adjustment threads. Dual-handle design allows for two-person leverage on larger pipes.
