Dichtomatik 75102234 O-Ring, 336 Dash Number, 2.85 in ID x 3.27 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number75102234
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialFKM
-
ColorBlack
-
Inside Diameter2.85 in
-
Domestic/ImportImport
-
Durometer75 Shore A
-
Outside Diameter3.27 in
- Good chemical resistance to mineral oils and greases, synthetic oils and greases, motor, transmission and ATF oils up to 150 deg C
- Very good weathering, ozone and aging resistance
- Very low gas permeability
-
UNSPSC31401503
-
Standards/ApprovalsASTM D1418|AS 568B|BS 1806|JIS 2401
-
Alternative Part NumberV75336
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
Dichtomatik 75102234 O-Ring, 336 Dash Number, 2.85 in ID x 3.27 in OD, FKM, 75 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
1/2" BLACK STREET ELBOW 3000#-FIT1/2BSTE3000 >
Chicago Pneumatic CP-9429-H Ratchet Wrench, 1/2 in Drive, 70 N-m Torque, 150 rpm Speed, 15 cfm Air Flow, 90 psi
The CP828 series pneumatic ratchet wrench is designed for general maintenance with its torque of 50 ft.lbs / 70 Nm. The CP828 Series is composed of 2 models: 3/8 Inch and 1/2 Inch anvil.
For use in extremely tight places, mini tubing cutters require minimal swing around the tubing. Mini tubing cutters can be used on copper, steel, stainless steel and aluminum tubing. MC2GRIP has rounded corners and edges of the body for a more comfortable grip when rotating the cutter around tubing. After tightening the feed screw, mini tubing cutters work faster by providing a more consistent cutting force on the wheel.
TB Wood's® synchronous Plus synchronous drives offer the added flexibility of a dual sprocket design that features both metric and standard-tapped holes coupled with a high-capacity synchronous Plus belt. As a result, the synchronous Plus drive offers a significantly higher horsepower rating at the standard industry price.
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
