Dichtomatik N70246 O-Ring, 246 Dash Number, 4.484 in ID x 4.762 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 246
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70246
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter4.484 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter4.762 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
MARXMANā¢ 85071 330QI General Purpose Jobber Length Drill Bit, #17 Drill - Wire, 0.173 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMANā¢ 85007 330QI General Purpose Jobber Length Drill Bit, 11/64 in Drill - Fraction, 0.1719 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
COMMERCIAL HEAVY-DUTY MOP HANDLE. 60" STEEL HANDLE WITH A FIRM GRIP VINYL COATING WITH RIBS TO PREVENT SLIPPING. THE MOPHEAD FEATURES A WING NUT THREADED LOCK. TO OPEN OR CLOSE THE MOUTH OF THE MOP HANDLE TIGHTEN OR LOOSEN THE WING NUT ON THE CENTER THREAD. INSERT THE MOPHEAD THROUGH THE OPENING AND THEN TIGHTEN THE WING NUT UNTIL THE MOUTH OF THE MOP HANDLE IS SECURE. THE MOP HANDLE CAN HOLD MOPS UP TO 32 OZ. SECURLY WITHOUT OPENING THE MOUTH OF THE MOP HANDLE OR BREAKING THE MECHANISM.
-JWH642266>
Amboreā¢ 12078 1384 Heavy Duty Jobber Length Drill Bit, 5/16 in Drill - Fraction, 0.3125 in Drill - Decimal Inch, 135 deg Point, HSS, Black/Gold Oxide
MORSEĀ® 51120 5374 Standard Length Jobber Length Drill Bit, 11/32 in Drill - Fraction, 0.3438 in Drill - Decimal Inch, 118 deg Point, Solid Carbide, Bright
