Dichtomatik N70145 O-Ring, 145 Dash Number, 2.55 in ID x 2.756 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70145
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter2.55 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter2.756 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70145 O-Ring, 145 Dash Number, 2.55 in ID x 2.756 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Precision Brand® 17S5 Shim Stock, 260 Half Hard Brass, 100 in Roll L x 6 in W x 0.005 in THK
Brass shim is made from a half hard, cold rolled, 260 alloy brass. Precision Brand® is the only manufacturer to offer Branded® shim. It has everything the user needs to know clearly marked right on the shim: material type, material thickness and lot # for full traceability. Used in applications where corrosion problems exist, low magnetic permeability. Excellent forming qualities and may be lightly drawn, blanked or stamped. Precision Brand® shim stock is widely used in the following applications: tool and die set up, alignment, new machine assembly, machine repair and maintenance, mounting of motors, pumps and other machines, short run and prototype work, along with a variety of other industrial uses. It is especially useful for pilot production runs where material accuracy and economy are important. All Precision Brand® shim products are manufactured under rigorous quality control standards to assure high accuracy and tight tolerances.
9-10" TERRY CLOTH POLISHING BONNET-JWH582158 >
MORSE® 43560 1897 Non-Center Cutting Regular Length Single End End Mill, 2 in Dia Cutter, 2 in Length of Cut, 8 Flutes, 3/4 in Dia Shank, 4-1/16 in OAL, Bright
MORSE® 43560 1897 Non-Center Cutting Regular Length Single End End Mill, 2 in Dia Cutter, 2 in Length of Cut, 8 Flutes, 3/4 in Dia Shank, 4-1/16 in OAL, Bright
Starrett® 178A Fillet/Radius Gage With Locking Device, 1/32 to 1/4 in, 30 Leaves, Stainless Steel
The Starrett 178 Series Fillet or Radius Inch Reading Gages are very useful for tool and diemakers, machinists, screw machine operators, patternmakers and other mechanics to lay out and check radii of tools, dies, patterns, and more. 30 Leaves, 1/32-1/4" Range, 64ths increments.
2517B Dodge® 120013 Keyseated Taper Locking Bushing Adapter, 4-1/8 in Dia, 1-3/4 in L, For Use With 2517 Bushing, Cast Iron
2517B Dodge® 120013 Keyseated Taper Locking Bushing Adapter, 4-1/8 in Dia, 1-3/4 in L, For Use With 2517 Bushing, Cast Iron
