Dichtomatik N70134 O-Ring, 134 Dash Number, 1.862 in ID x 2.068 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 134
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70134
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter1.862 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter2.068 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
-
Catalog
-
Instruction/Installation Manual
-
Specification Sheet
Recently Viewed
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
United Abrasives-SAIT 84918 DAF Sanding Sheet, 11 in L x 9 in W, 320 Grit, Aluminum Oxide Abrasive, Cloth Backing
35-MM-ID 3-PIECE THRUST BALL BEARING-GUL907 >
67.6-OZ(2-L) PURELL HAND SANITIZER-GOJ9625>
IKO IRB2424 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 38.48 mm OAW, For Use With BA2824Z and BHA2824Z Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
Weiler® 99383 Small Handle Straight Scratch Brush, 1-3/4 in Brush, 6-1/2 in L x 1/2 in W Block, 1/2 in L Nylon Trim
Weiler® 99383 Small Handle Straight Scratch Brush, 1-3/4 in Brush, 6-1/2 in L x 1/2 in W Block, 1/2 in L Nylon Trim
