Dichtomatik 67002762 O-Ring, 63 mm ID x 73 mm OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part Number67002762
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter63 mm
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter73 mm
- Good chemical resistance to mineral oils and greases
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
-
Alternative Part NumberN5.00X063
-
Instruction/Installation Manual
-
Specification Sheet
-
Catalog
Recently Viewed
Dichtomatik 67002762 O-Ring, 63 mm ID x 73 mm OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
BBI 087222 Fully Threaded Cap Screw, 7/16-14, 1-1/2 in L Under Head, 5 Grade, Carbon Steel, Zinc CR+3
BBI 087222 Fully Threaded Cap Screw, 7/16-14, 1-1/2 in L Under Head, 5 Grade, Carbon Steel, Zinc CR+3
6" FLEX BROAD KNIFE-JWH774782 >
NIBCO 854-100 Loose Ring Flange, 10 in Nominal, PVC, Socket Connection, Domestic
Loose Ring Flange, 10 in Nominal, PVC, Socket Connection, Domestic
IKO LRB81212 Inch Series Inner Ring With Oil Groove, 1/2 in ID x 3/4 in OD, 19.3 mm OAW, For Use With BR122012 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
HOT-DIPPED STEEL CONSTRUCTION IS DIPPED IN A BATH OF MOLTEN ZINC TO COAT AND SEAL. REINFORCED WIRE RIM. WEATHER AND RUST RESISTANT. SUITABLE FOR DRY OR LIQUID STORAGE.
-JWH624337 >
