ITM 201SD6364 Bit Shank Drill, 63/64 in Drill - Fraction, 1.0625 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
ITM 201SD6364 Bit Shank Drill, 63/64 in Drill - Fraction, 1.0625 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
-
BrandITM
-
UPC703652463611
-
Manufacturer Part Number201SD6364
-
CountryUSA
-
FinishBlack Oxide
-
Point Angle118 deg
-
MaterialM2 HSS
-
Flute Length2-3/4 in
-
Flute TypeGround
-
TypeBit
-
Applicable MaterialsSteel/Mild Stainless/Cast Iron
-
Shank Size1/2 in
-
Drill Size - Decimal Inch1.0625
-
Drill Size - Fraction63/64 in
-
Overall Length6 in
-
Catalog
Recently Viewed
ITM 201SD6364 Bit Shank Drill, 63/64 in Drill - Fraction, 1.0625 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
ITM 201SD6364 Bit Shank Drill, 63/64 in Drill - Fraction, 1.0625 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
DeWALT® DW5446 Masonry Drill Bit, 5/8 in Drill Bit, 25/64 in SDS-Plus Shank, 6 in D Cutting, Carbide Cutting Edge, 8 in OAL
DeWalt® solid Rock Carbide™ SDS Plus® drill bit delivers the best in durability and long life, so you can work confidently without worrying about the tool. With four cutter heads and two times more carbide than competitive two cutter bits, this bit is tough across multiple drilling operations, even in reinforced concrete. An innovative bonding system attaches the tip to the flute and ensures that the bit will last. DeWalt® strives to increase your efficiency on the job and the SDS Plus® bit has a 4-flute design that removes debris while you work.
Milwaukee® Tapcon™ 48-20-7091 2-Cutter Rotary Hammer Drill Bit With 1/4 in Hex Shoulder, 5/32 in Drill Bit, 1/4 in SDS Shank, 4 in D Cutting, Carbide Cutting Edge, 7 in OAL
The Milwaukee® SDS Plus bits with 1/4 in. hex are designed specifically for TAPCON® screw applications. Built to take on brick, block, and concrete Milwaukee SDS Plus Bits feature 2-cutter geometry for fast drilling and debris removal. The patented, reinforced flute design increases impact resistance and transfers energy directly to the bit tip. Patented rebar chamfers withstand impact from rebar and hard aggregate, and reduce Carbide chipping. To be used with drive sleeve available in the SDS Plus TAPCON® installation kit (48-20-7497). TAPCON® is a registered trademark of Illinois tool works Inc.
Mayhewâ„¢ 10205 PROâ„¢ Full Finish Cold Chisel, Beveled Tip, 6 in OAL, 1/2 in W Blade
Mayhewâ„¢ 10205 PROâ„¢ Full Finish Cold Chisel, Beveled Tip, 6 in OAL, 1/2 in W Blade
DW-9310 BLACK & DECKER/DEWALT
7.2 VOLT TO 18 VOLT BATTERY CHARGER-BD-DC9310>
ITM 201SD4364 Bit Shank Drill, 43/64 in Drill - Fraction, 0.6719 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
ITM 201SD4364 Bit Shank Drill, 43/64 in Drill - Fraction, 0.6719 Drill - Decimal Inch, 1/2 in Shank, M2 HSS
