Torque Limiter Parts
Browning® 1304823 Replacement Bearing
Browning® 1304823 Replacement Bearing
Browning® 1304849 Replacement Bearing
Browning® 1304849 Replacement Bearing
Browning® 1304856 Replacement Bearing, For Use With Torq/Gard® T65L Model Torque Limiter
Browning® 1304856 Replacement Bearing, For Use With Torq/Gard® T65L Model Torque Limiter
Browning® 1304898 Replacement Spring, For Use With Torq/Gard® T55L Model Torque Limiter
Browning® 1304898 Replacement Spring, For Use With Torq/Gard® T55L Model Torque Limiter
Morse® 100522 Pressure Plate, For Use With Model 500A Plain Bore Torque Limiter
Morse® 100522 Pressure Plate, For Use With Model 500A Plain Bore Torque Limiter
Morse® 604001 Unbonded Friction Facing
Morse® 604001 Unbonded Friction Facing
Morse® 604101 Unbonded Friction Facing
Morse® 604101 Unbonded Friction Facing
Morse® 604103 Lock Washer, For Use With Model 350A Plain Bore Torque Limiter
Morse® 604103 Lock Washer, For Use With Model 350A Plain Bore Torque Limiter
Morse® 604106 Bushing
Sintered steel bushing on which the center member and friction facings rides are coated with a dry film lubricant; therefore, no oil is present to contaminate friction facings and reduce torque capacity. The bushing "free floats" on the hub. Morse® offers a wide selection of bushing widths in all torque limiter sizes, permitting close matching of center member and bushing width to minimize bearing pressure and promote longer bushing life.
Morse® 604107 Bushing
Sintered steel bushing on which the center member and friction facings rides are coated with a dry film lubricant; therefore, no oil is present to contaminate friction facings and reduce torque capacity. The bushing "free floats" on the hub. Morse® offers a wide selection of bushing widths in all torque limiter sizes, permitting close matching of center member and bushing width to minimize bearing pressure and promote longer bushing life.
Morse® 604201 Unbonded Friction Facing
Morse® 604201 Unbonded Friction Facing
Morse® 604205 Bushing
Sintered steel bushing on which the center member and friction facings rides are coated with a dry film lubricant; therefore, no oil is present to contaminate friction facings and reduce torque capacity. The bushing "free floats" on the hub. Morse® offers a wide selection of bushing widths in all torque limiter sizes, permitting close matching of center member and bushing width to minimize bearing pressure and promote longer bushing life.
Morse® 604208 Bushing
Sintered steel bushing on which the center member and friction facings rides are coated with a dry film lubricant; therefore, no oil is present to contaminate friction facings and reduce torque capacity. The bushing "free floats" on the hub. Morse® offers a wide selection of bushing widths in all torque limiter sizes, permitting close matching of center member and bushing width to minimize bearing pressure and promote longer bushing life.
Recently Viewed
PTI 10B-31B Single Strand Hub Type B Roller Chain Sprocket, 20 mm Dia Bore, 163.9 mm OD, #10B-1 Chain, 31 Teeth, 15.875 mm Pitch, C45 Steel
Hub type metric sprockets are available with a minimum plain bore (pilot bore) and some stock finished bore sizes. Any shaft size is possible with our custom bore and keyway capability. Sprockets with hubs are typically fitted to the shaft as a clearance fit. They are held in place with two set screws and a keyway. Clearance fits are popular for light loads and slow speeds. A press fit (or shrink fit to the shaft) is usually preferred for higher speeds or heavier loads as they fit to the shaft more securely than a clearance fit sprocket. Depending on the clearance of the shaft fit, sprockets may work slightly on the shaft causing possible fretting or shaft wear. All sprockets are available with hardened teeth from stock or on request. Press fits usually require the sprocket to be heated for installation to expand the bore. As a heated sprocket cools, it shrinks, conforming to the shaft with a tight grip. A set screw can be used to secure the key. The TL taper bushed sprocket will function like the press fit sprocket and is generally easier to install.
The Armstrong 28-330 is a premium industrial-grade 15/16" 12-point ratcheting flare nut wrench. Designed for use on tube fittings, valves, compression fittings, and fasteners, it features a ratcheting box end. The design lets you tighten and loosen fittings in tight spaces without removing the wrench from the nut.
2" X 30" NICKEL CONTINUOUS HINGES-NTL148270 >
Features:
Hardened for extra strength
Withstands stress under impact
Prevents rounding of fasteners' corners
"Lobular" design exerts force on flats of fasteners
Chamfered opening slips easily over fasteners and holds securely
Specifications:
No. of Points: 12
Opening: 1-1/2"
Weight: 3.56 lb
Overall Length: 11.75"
Head Thickness: 1.0"
Offset Height: 1.5"
Head Diameter: 2.187"
Handle Width: 1.343"
Handle Height: 1.343
Handle Length: 3.375"
Armstrong Industrial Tools 33-048 12 Point 45 Degree Offset Slugging Wrench 1-1/2"
60032 Mounted Points-3/4" X 1/4" A24 Maxrpm: 56.000. Shank Mounted Points And Grinding Wheels Are Made From Durable High Grade 60 Grit Aluminum
MOUNTED POINTS-3/4" X 1/4" A24 MAXRPM: 56.000. SHANK MOUNTED POINTS AND GRINDING WHEELS ARE MADE FROM DURABLE HIGH GRADE 60 GRIT ALUMINUM OXIDE-FOR60032 >
3" RUBBER BACKING PAD-FOR60271 >
