Martin 41A54 Stock Bore Type A Single Pitch Roller Chain Sprocket, 23/32 in Dia Bore, 8.885 in OD, #41 Chain, 54 Teeth, 1/2 in Pitch, Steel
A plates are flat sprockets with no hub extension on either side. They can be altered for your application with bolt holes, custom bores, hardened teeth or special hubs welded to them.
-
BrandMartin
-
UPC697950009605
-
Manufacturer Part Number41A54
-
CountryUSA|Canada
-
Pitch1/2 in
-
Pitch Diameter8.599 in
-
MaterialSteel
-
Chain Size#41
-
TypeStock Bore Type A
-
Number of Teeth54
-
Outside Diameter8.885 in
-
Length Through Bore0.227 in
-
Bore Diameter23/32 in
- Plate only
- Precise machining and processes ensure consistent finish and high quality
-
UNSPSC31171901
-
Standards/ApprovalsPROP65: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
-
Catalog
Recently Viewed
Martin 41A54 Stock Bore Type A Single Pitch Roller Chain Sprocket, 23/32 in Dia Bore, 8.885 in OD, #41 Chain, 54 Teeth, 1/2 in Pitch, Steel
A plates are flat sprockets with no hub extension on either side. They can be altered for your application with bolt holes, custom bores, hardened teeth or special hubs welded to them.
#14 X 1-1/4" Bonded Hex Tek-3 Screws
Permatex® 81630 ULTRA RED® Silicone Gasket Maker, 3 oz Container Carded Container
Permatex® 81630 ULTRA RED® Silicone Gasket Maker, 3 oz Container Carded Container
MCR Safety 411150 Foreman® Safety Glasses, Duramass® Hard Coat, Green Lens, Brown, Polycarbonate Frame, ANSI Z87.1-2003, CSA Z94.3
MCR Safety 411150 Foreman® Safety Glasses, Duramass® Hard Coat, Green Lens, Brown, Polycarbonate Frame, ANSI Z87.1-2003, CSA Z94.3
Edison ECNR9 ECNR Current Limiting Time Delay Fuse, 9 A, 250 V AC/125 V DC, 200 kAIC Interrupt, Class: RK5, Cylindrical Body
Edison's UL Class RK5 dual-element, time-delay fuses provide economical solutions to overcurrent protectioni. Available in both 250Vac and 600Vac, with 200kA RMS Sym interrupting ratings and sizes ranging from 0 to 600 amp.
IKO IRB1612 Inch Series Inner Ring, 1 in ID x 1-1/4 in OD, 19.43 mm OAW, For Use With BA2012Z/BHA2012Z and YB2012 Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
