Browning 14-TOOTH #40-1 CHAIN SPROCKETS BRW H-4014 X 1-1/8
Browning® finished bore sprockets are offered in single strands. Offerings include 35 to 100 pitch range. Finished bore sprockets are available from 3/8 to 2-7/16 in. Hardened teeth are available up to 30 teeth.
-
BrandBrowning®
-
UPC662289243044
-
Manufacturer Part Number1128131
-
CountryUSA
-
Pitch Diameter2.247 in
-
MaterialSteel
-
Chain Size#40
-
TypeSingle Strand Finished Bore Type 1
-
Hub Diameter1.8906 in
-
Number of Teeth14
-
Outside Diameter2.49 in
-
Length Through Bore0.891 in
-
Bore Diameter1-1/8 in
- Furnished with standard keyway on centerline of tooth and hollow head setscrew over keyway
- In-stock hardened sprockets are warranted to last at least twice as long as the standard (unhardened) mild steel sprockets they replace
- For use with 1/2 in pitch ANSI chain
- Additional setscrew at 90 deg to keyway
-
Alternative Part NumberH4014X 1 1/8
-
UNSPSC31171901
-
Package Description1/PK
-
Warranty1 Year
-
Warranty Information
-
Specification Sheet
Recently Viewed
Browning 14-TOOTH #40-1 CHAIN SPROCKETS BRW H-4014 X 1-1/8
Browning® finished bore sprockets are offered in single strands. Offerings include 35 to 100 pitch range. Finished bore sprockets are available from 3/8 to 2-7/16 in. Hardened teeth are available up to 30 teeth.
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11378 1330 General Purpose Jobber Length Drill Bit, 3/64 in Drill - Fraction, 0.0469 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
MORSE® 16771 1391 Aircraft Extension Drill, #42 Drill - Wire, 0.0935 in Drill - Decimal Inch, 135 deg Point, HSS
IKO LRB121612 Inch Series Inner Ring With Oil Groove, 3/4 in ID x 1 in OD, 19.3 mm OAW, For Use With BR162412 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
MARXMAN™ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MARXMAN™ 85068 330QI General Purpose Jobber Length Drill Bit, #14 Drill - Wire, 0.182 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
7 LB BOX OF CEMENT BASE WITH SILICA SAND RESULTING IN DENSE, HARD JOINTS WITHOUT CRACKING OR SHRINKING. PEWTER. SOLD IN-JWH284637 >
