Browning 14-TOOTH L-PITCH T/BELT SHEAVES BRW 14-L-F-075 X 1/2
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
-
BrandBrowning®
-
UPC662289111824
-
Manufacturer Part Number1054600
-
CountryUSA
-
Face Width1 in
-
Pitch3/8 in
-
Pitch Diameter1.671 in
-
Flange Diameter1-15/16 in
-
TypeType 1
-
Hub Diameter1-1/8 in
-
Hub Projection1/2 in
-
Number of Grooves14
-
Outside Diameter1.641 in
-
Bore Diameter1/2 in
-
Bore TypeFinished
-
Overall Length1-1/2 in
-
Suitable For Use With3/4 in W Type L075 Belt
- Constant Speed - No slip, no creep, minimum backlash due to the positive engagement of the belt teeth with the grooves of the sprockets
- Broad depth of product to choose from - Browning offers 5 different sprocket pitches along with a wide range of sprocket and belt widths to accommodate any horsepower requirement
- Different Mounting to the shaft - Browning offers the Gearbelt Pulleys in various ways to mount to the shaft, Split Taper and QD Bushing styles, as well as, finished and minimum plain bore
- Lightweight, high horsepower-to-weight ratio makes Gearbelt® drives ideal for any application where weight is an important factor
- Less heat, because Gearbelt® drives generate virtually no friction
- No lubrication required
- Wide load capacity range
- Constant Speed - No slip, no creep, minimum backlash due to the positive engagement of the belt teeth with the grooves of the sprockets
- Different Mounting to the shaft - Browning offers the Gearbelt Pulleys in various ways to mount to the shaft, Split Taper and QD Bushing styles, as well as, finished and minimum plain bore
- Largest selection in the Industry - Browning offers the widest range of variable speed sheaves in the market today
- One and two Groove product are available in 1.6 in to 8.5 in covering up to 25 horsepower
- VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore
- The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with
- When discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed
- Broad depth of product to choose from - Browning offers 5 different sprocket pitches along with a wide range of sprocket and belt widths to accommodate any horsepower requirement
-
Alternative Part Number14LF075X1/2
-
UNSPSC26111807
-
Package DescriptionEACH
-
Warranty1 Year
-
Instruction/Installation Manual
Recently Viewed
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
PR14-5B-T by Coilhose | Flexcoil Air Hose | 1/4" Hose ID x 3/8" Hose OD | 1/4" Male NPT Reusable Swivel | Transparent Blue | Polyurethane | 5ft
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
Knipex® Cobra® 87 01 125 SBA Box Joint Fully Fledged High Tech Water Pump Plier, 1 in Nominal, 13/16 in L x 3/4 in W CRV Steel V-Shape Jaw, Serrated Jaw Surface, 5 in OAL
The special jaw design with opposing off-set teeth ensures maximum grip and perfect alignment. In addition the Cobra® offers a unique adjustment mechanism: at the push of a button the tool adjusts fast and easily to the workpiece. No more guessing at the right size. To the contrary: place the upper part of the jaw against the workpiece, press button and push the lower jaw into position. Simply perfect. The button serves as a memory button: an unintentional adjustment - even under load - is not possible. The fine adjustment always provides a favorable position of the handles. Also in this respect the ergonomically designed Cobra® is particularly user friendly.
HCI Preferred Supplier 940464 3-Way Ball Valve, 1/4 in Nominal, FIPT End Style, Forged Brass Body, Full Port, PTFE Seal/PVC Cover/NBR O-Ring Softgoods
HCI Preferred Supplier 940464 3-Way Ball Valve, 1/4 in Nominal, FIPT End Style, Forged Brass Body, Full Port, PTFE Seal/PVC Cover/NBR O-Ring Softgoods
SMALL LOVING HAND GLOVES-JWH624818>
