GatesĀ® Power Transmission 4430V555 Banded Multi-Speed V-Belt, 2-3/4 in W Top, 30 deg Groove, 56-1/2 in L Outside, Rubber
Multi-speed belts are made banded or bandless construction featuring high-modulus, fiber-loaded stock that offers transverse rigidity and flexibility at the same time. This results in higher load carrying capacity and long belt life.
-
BrandGatesĀ® Power Transmission
-
UPC072053281859
-
Manufacturer Part Number4430V555
-
CountryUSA
-
MaterialRubber
-
Top Width2-3/4 in
-
Reinforced MaterialPolyester
-
TypeBanded
-
Groove Angle30 deg
-
Series9800
-
Outside Length56-1/2 in
- Notch design reduced thermal and bending stresses for longer life
- Smooth running construction for minimal vibration at high speeds
-
Alternative Part Number98000132
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
GatesĀ® Power Transmission 4430V555 Banded Multi-Speed V-Belt, 2-3/4 in W Top, 30 deg Groove, 56-1/2 in L Outside, Rubber
Multi-speed belts are made banded or bandless construction featuring high-modulus, fiber-loaded stock that offers transverse rigidity and flexibility at the same time. This results in higher load carrying capacity and long belt life.
GatesĀ® Power Transmission 4830V699 Banded Multi-Speed V-Belt, 3 in W Top, 30 deg Groove, 71 in L Outside, Rubber
Multi-speed belts are made banded or bandless construction featuring high-modulus, fiber-loaded stock that offers transverse rigidity and flexibility at the same time. This results in higher load carrying capacity and long belt life.
HougenĀ® 12224 12000 Annular Cutter, 3/4 in Dia Cutter, 2 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
MIG CONTACT TIP .024 FITS FORNEY 304, 306, AND 308-FOR85346 >
IDEALĀ® 774008 Standard Toggle Switch, 125/227 V AC, 20/10 A, 3/4 hp Power Rating, On-Off SPST Contact
IDEALĀ® 774008 Standard Toggle Switch, 125/227 VAC, 20/10 A, 3/4 hp Power Rating, SPST ON-OFF Contact
MORSEĀ® 59004 5968 Center Cutting High Performance Regular Length Single End End Mill, 3/16 in Dia Cutter, 0.03 in Corner Radius, 5/8 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Bright
MORSEĀ® 59004 5968 Center Cutting High Performance Regular Length Single End End Mill, 3/16 in Dia Cutter, 0.03 in Corner Radius, 5/8 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Bright
