Gates® Power Transmission Hi-Power® II BB73 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 76 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
-
BrandGates® Power Transmission
-
UPC72053203561
-
Manufacturer Part NumberBB73
-
CountryUSA|Canada
-
Thickness17/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter5.73 in
-
Section SizeBB
-
Series9053
-
Number of Ribs1
-
Outside Length76 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
-
Alternative Part Number90530073
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II BB73 Banded Heavy Duty Double V-Belt, BB Section, 21/32 in W Top, 76 in L Outside, 17/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
Dodge® 023098 111 Non-Expansion Type E-Xtra Triple Lip Flange Mount Roller Bearing Unit, 1-5/8 in Dia Bore, 4.13 in L Bolt Center-to-Center, 4-Bolt Base Flange Mount, 5.38 in OAL/Dia
Dodge® 023098 111 Non-Expansion Type E-Xtra Triple Lip Flange Mount Roller Bearing Unit, 1-5/8 in Dia Bore, 4.13 in L Bolt Center-to-Center, 4-Bolt Base Flange Mount, 5.38 in OAL/Dia
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
N-95 SMALL DUST RESPIRATORS-MOLEZ23S >
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
ADS® 0422AA Corrugated Single Wall Drain Wye, 4 in, Slip, HDPE, Domestic
ADS® 0422AA Corrugated Single Wall Drain Wye, 4 in, Slip, HDPE, Domestic
