Gates® Power Transmission Hi-Power® II AA75 Banded Heavy Duty Double V-Belt, AA Section, 1/2 in W Top, 77 in L Outside, 13/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
-
BrandGates® Power Transmission
-
UPC72053200102
-
Manufacturer Part NumberAA75
-
CountryUSA|Canada
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.138 in
-
Section SizeAA
-
Series9052
-
Number of Ribs1
-
Outside Length77 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
-
Alternative Part Number90520075
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II AA75 Banded Heavy Duty Double V-Belt, AA Section, 1/2 in W Top, 77 in L Outside, 13/32 in THK, EPDM
Designed with a unique recessed top and bottom to maintain sidewall contact, while remaining flexible for belt drive applications that require power transmission from both sides of the belt.
MORSE® 58154 5955 Center Cutting Long Length Single End End Mill, 3/8 in Dia Cutter, 1-1/8 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3 in OAL, Bright
MORSE® 58154 5955 Center Cutting Long Length Single End End Mill, 3/8 in Dia Cutter, 1-1/8 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 3 in OAL, Bright
Weiler® 08085 Wheel Brush, 6 in Dia Brush, 1/2 in W Face, 0.014 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
Weiler® 6 in standard twist knot wire Wheel Brush provides a heavy duty brushing action with some flexibility for demanding deburring cleaning and surface preparation applications on somewhat irregular surfaces. Featuring Weiler® individual knot hole construction, these radial brushes are available in heat treated steel, type 302 stainless steel and bronze wire for use in a wide variety of applications. 5/8 to 1/2 in arbor hole for use on bench/pedestal grinder, die grinder, right angle die grinder and straight grinders.
3/4" -ID 2-BOLT FLANGE UNIT-MBUVF2S212 >
Jacobs® 7343N Spindle Drill Chuck Arbor, #33 JT Mount Taper, 0.56 to 0.62 in Dia Bridgeport® Taper Shank, R8 Shank Taper
Jacobs® 7343N Spindle Drill Chuck Arbor, #33 JT Mount Taper, 0.56 to 0.62 in Dia Bridgeport® Taper Shank, R8 Shank Taper
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
