Gates® Power Transmission Hi-Power® II PowerBand® 2/C124 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 128 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053243772
-
Manufacturer Part Number2/C124
-
CountryUSA|Canada
-
Thickness17/32 in
-
MaterialEPDM
-
Top Width7/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter7.958 in
-
Section SizeC
-
Series9094
-
Number of Ribs2
-
Outside Length128 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Concave sidewalls provide proper cord support and full contact with the sheave groove for equal loading and uniform wear
-
Alternative Part Number90942124
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II PowerBand® 2/C124 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 128 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Gates® Power Transmission Poly Chain® GT® Carbon™ 14MGT-1890-68 Synchronous Belt, 68 mm W, 1890 mm OAL, 14 mm Pitch, 135 Teeth, Polyurethane
Give yourself a competitive advantage by designing in the Gates Poly Chain™ GT™ Carbon drive system instead of roller chain in your next power transmission application. The patented use of carbon fiber as the tensile cord in this belt provides increased horsepower rating for greater power density and compactness. When combined with Gates Poly Chain GT sprockets, you have a lightweight, long-lasting, maintenance-free system that's more than a match for roller chain.
Smith Bearing® CR-3-XB Cylindrical Stud Type Needle Bearing Cam Follower, 3 in Dia x 1-3/4 in W Roller, 1-1/4 in Dia x 2-1/2 in L Stud, 52100 Steel Roller
Hex head stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel.
Smith Bearing® CR-5/8-X Cylindrical Stud Type Needle Bearing Cam Follower, 5/8 in Dia x 7/16 in W Roller, 1/4 in Dia x 3/4 in L Stud, 52100 Steel Roller
Screwdriver slot stud type needle roller bearings are recommended where running loads and shock loads are moderate. Bearing capacity of the stud type series is limited by the moderately sized stud. Manufactured from high alloy bearing quality steel. Most commonly used general purpose cam follower and available in sealed versions.
