Gates® Power Transmission Tri-Power® PowerBand® 4/BX74 Heavy Duty Molded Notch V-Belt, BX Section, 21/32 in W Top, 77.6 in L Outside, 13/32 in THK, EPDM
Built for superior performance on heavy duty classical cross-section drives. The raw edge, Ethylene Elastomer construction and special notch design makes the Tri-Power belt especially suited for small diameter pulleys and back side idler drives.
-
BrandGates® Power Transmission
-
UPC72053506945
-
Manufacturer Part Number4/BX74
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Section SizeBX
-
Series9098
-
Number of Ribs4
-
Outside Length77.6 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- Belt edge is machined for even sheave groove contact resulting in smoother running, less slip and wear
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number90984074
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Tri-Power® PowerBand® 4/BX74 Heavy Duty Molded Notch V-Belt, BX Section, 21/32 in W Top, 77.6 in L Outside, 13/32 in THK, EPDM
Built for superior performance on heavy duty classical cross-section drives. The raw edge, Ethylene Elastomer construction and special notch design makes the Tri-Power belt especially suited for small diameter pulleys and back side idler drives.
TRAILER ADAPTER-JWH585653 >
Drillco 73A112C 7300 Center Cutting Imperial Regular Length Single End Finishing End Mill, 3/16 in Dia Cutter, 5/8 in Length of Cut, 4 Flutes, 3/16 in Dia Shank, 2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 72A164C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 1 in Dia Cutter, 1-1/2 in Length of Cut, 2 Flutes, 1 in Dia Shank, 4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 72A120C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 5/16 in Dia Cutter, 13/16 in Length of Cut, 2 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
Drillco 72A140C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 5/8 in Dia Cutter, 1-1/4 in Length of Cut, 2 Flutes, 5/8 in Dia Shank, 3-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
