McGill 7/8"-ID NEEDLE BEARINGS MCG MR-14-N
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
-
BrandMcGill®
-
UPC726166065225
-
Manufacturer Part Number5451460000
-
CountryUSA
-
Load Capacity5280 lb Dynamic/6000 lb Static
-
Cage MaterialSteel
-
Temperature Rating-20 to 250 deg F
-
Maximum Speed13750 rpm
-
Closure TypeUnsealed
-
TypeHeavy Duty Narrow
-
Width3/4 in
-
SeriesMR Series
-
Number of Rows1
-
Bearing Material52100 Steel
-
Outside Diameter1-3/8 in
-
Bore Diameter7/8 in
- Machined outer race
- Needle roller with end relief
- Annular lubrication groove and holes
- Factory grease fill
- Narrow width
-
Alternative Part NumberMR 14 N
-
UNSPSC31171542
-
Package DescriptionEACH
-
Specification Sheet
-
Catalog
Recently Viewed
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
3/8" -MALE PIPE THREADX8-FEMALE JIC HYDRAULIC ADAPTER-DAY650568 >
Type S flanges sizes 6 through 16 are manufactured of high strength cast iron then bored-to-size for slip fit on standard shafts. Size 5 is made of sintered carbon steel. Flanges are easy to install and remove, and are stocked in a wide range of bore sizes. All sleeve materials may be used with type S flanges.
Gates® Power Transmission Super HC® Molded Notch PowerBand® 4/5VX1400 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 140 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
84" VERTICAL SCHULTE SHELVING POLE-JWH217905>
BUGLE HEAD COARSE THREAD. FOR ATTACHING GYPSUM BOARD TO WOOD STUDS. NO. 2 REDUCED PHILLIPS RECESS. THIS SCREW IS CONSTRUCTED OF HARDENED STEEL WHICH IS THE RESULT OF CARBON STEEL BEING PUT THROUGH HEAT TREATMENT, QUENCHING, NAD FURTHER REHEATING MAKING IT EXTREMELY DURABLE. HARDENED STEEL IS MORE RESISTANT TO WEAR, CORROSION, AND ABRASION.
-JWH701386 >
