McGill® 0001630000 MI Series Narrow Machined Separable Inner Ring With Oil Hole and Annular Groove, 1 in ID x 1.2491 in OD, 1.01 in OAW, For Use With GUIDEROL® GR 20 N, CAGEROL® MR 20 N Bearing, Chrome Steel
Precision ground inner ring provides a hardened raceway for the rollers when used with an unhardened shaft. The ring contains an oil hole and annular groove for relubrication of the bearing and can be used with both CAGEROL® and GUIDEROL® bearings or can be utilized as a bushing in plain bearing applications.
-
BrandMcGill®
-
UPC726166000226
-
Manufacturer Part Number0001630000
-
CountryUSA
-
Lubrication Hole TypeLubrication Hole
-
MaterialChrome Steel
-
TypeNarrow
-
SeriesMI Series
-
Inside Diameter1 in
-
Outside Diameter1.2491 in
-
Bore TypeRound/Spherical
-
Overall Width1.01 in
-
Suitable For Use WithGUIDEROL® GR 20 N, CAGEROL® MR 20 N Bearing
- AMBA standard 18.2 precision rating
- Thru hardened precision ground rings construction
-
Alternative Part NumberMI 16 N
-
UNSPSC31171500
-
Standards/ApprovalsMS 51962-10
-
Specification Sheet
-
Catalog
Recently Viewed
McGill® 0001630000 MI Series Narrow Machined Separable Inner Ring With Oil Hole and Annular Groove, 1 in ID x 1.2491 in OD, 1.01 in OAW, For Use With GUIDEROL® GR 20 N, CAGEROL® MR 20 N Bearing, Chrome Steel
Precision ground inner ring provides a hardened raceway for the rollers when used with an unhardened shaft. The ring contains an oil hole and annular groove for relubrication of the bearing and can be used with both CAGEROL® and GUIDEROL® bearings or can be utilized as a bushing in plain bearing applications.
Koyo IR-101412 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 3/4 in OAW, For Use With HJ-142212 Heavy Duty Needle Roller Bearing, Steel
Koyo IR-101412 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 3/4 in OAW, For Use With HJ-142212 Heavy Duty Needle Roller Bearing, Steel
Koyo IR-88 Inch Series Regular Width Inner Ring, 1/2 in ID x 3/4 in OD, 0.515 in OAW, For Use With B-126, B-128, J-126, J-128, M-1261, M-1281 Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Koyo IR-2424 Inch Series Regular Width Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1.515 in OAW, For Use With Inch Series Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Koyo IR-242820 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1-1/4 in OAW, For Use With HJ-283720 Heavy Duty Needle Roller Bearing, Steel
Koyo IR-242820 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1-1/4 in OAW, For Use With HJ-283720 Heavy Duty Needle Roller Bearing, Steel
Koyo IR-2020 Inch Series Regular Width Inner Ring, 1-1/4 in ID x 1-1/2 in OD, 1.265 in OAW, For Use With B-268, B-2610, B-2616, J-2610, J-2616, M-26161, M-26101 Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
