Torrington NEDDLE BEARING INNER RACES TOR IR-1212
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
-
BrandKoyo
-
UPC605790195358
-
Manufacturer Part NumberIR-1212
-
CountryUSA
-
FinishPolished Chrome
-
MaterialSteel
-
TypeRegular Width
-
SeriesIR Inch Series
-
Inside Diameter3/4 in
-
Outside Diameter1 in
-
Overall Width0.765 in
-
Suitable For Use WithB-1610, B-1612, BH-1610, BH-1612, J-1612, JH-1612, M-16101, M-16121, MH-16121, MJH-16121 Drawn Cup Needle Roller Bearing
- Ideal choice when shaft is not practical to use as inner raceway
- Designed to meet established inch tolerances
- Designed to be wider than matching drawn cup bearing
- Maximum shaft fillet radius cannot exceed inner ring bore chamfer
- Designed to provide a loose transition fit on the shaft and should be axially clamped against a shoulder
- If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD must not exceed the raceway diameter for the matching drawn cup bearing after being mounted on the shaft
- After mounting, if OD of inner ring exceeds the required raceway diameter for matching bearing, ring should be ground to proper diameter while mounted to shaft
| Competitor Name | Cross-Reference Number |
|---|---|
| Grainger | 779KE6 |
-
Alternative Part NumberIR1212PBL125
-
UNSPSC31171547
-
Catalog
Recently Viewed
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
JASON 4RB133 V-BELTS, TOP WIDTH .066" 21/32"4-RIBS 136" OUTSIDE LENGTH
THIS V-BELT IS OIL AND HEAT-RESISTANT. STATIC DISSIPATING. UNIMATCH BANDED V-BELTS ARE AVAILABLE IN CLASSICAL MULTIPLE SECTIONS. THEY FEATURE THE SAME PREMIUM CONSTRUCTIONS AS THE INDIVIDUAL BELT AND ARE BONDED.
-JAS4RB133 >
3/8" X 1/4" COPPER SWEAT REDUCERS-ELK1183/8X1/4>
Browning® 3749074 Taper Lock Bushing, 13/16 in Dia Bore, 2-1/4 in Dia Barrel, 1-1/2 in OAL, Steel
Browning® 3749074 Taper Lock Bushing, 13/16 in Dia Bore, 2-1/4 in Dia Barrel, 1-1/2 in OAL, Steel
Vortec Pro® 40029 Multi-Purpose Chip and Oil Brush, 3/8 in THK China Bristle Brush, Plastic Handle, Alkyd Paints, All Stains, Oil Paints, Shellacs, Urethane and Varnishes
Vortec Pro® 40029 Multi-Purpose Chip and Oil Brush, 3/8 in THK China Bristle Brush, Plastic Handle, Alkyd Paints, All Stains, Oil Paints, Shellacs, Urethane and Varnishes
1-1/8" -ID LOW PILLOW BLOCK UNIT-FYHSL20618 >
