Dodge® 069412 Imperial Pillow Block Roller Bearing Unit, 2-3/16 in Dia Bore, 6.56 to 6.94 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8.88 in OAL x 5 in OAH
Dodge® imperial spherical roller bearings are the only high-capacity double-row spherical roller bearings with an effective easy-on, easy-off adapter mounting and removal system. Not only does this patented system provide a concentric grip for superior holding on the shaft, but it reduces the fretting corrosion caused by traditional setscrews and vibration.
-
BrandDodge®
-
UPC782475307708
-
Manufacturer Part Number069412
-
CountryUSA
-
Load Capacity27000 lb Dynamic/29000 lb Static
-
Locking DeviceAdapter Mounted
-
FinishUncoated
-
MaterialCast Iron
-
Maximum Speed3000 rpm
-
TypeImperial
-
Mounting TypeTwo-Bolt Base
-
Seal TypeTrident™ Triple Lip
-
Base Width2.63 in
-
Base to Bore Centerline2-1/4 in
-
Bolt Center-to-Center Length6.56 to 6.94 in
-
Bore Diameter2-3/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height5 in
-
Overall Length8.88 in
-
Overall Width3.03 in
- Push pull adapter mount
- Grease limiting speeds 30% higher than set screw mounts
- Patented adapter mounting system
- Superior holding power reduces the fretting corrosion caused by vibration
- Seal/land on OD of inner ring maintains full contact pressure even when misaligned
| Competitor Name | Cross-Reference Number |
|---|---|
| Applied Industrial Technologies | 100738750 |
| Motion Industries | 02317665 |
-
Alternative Part NumberP2B-IP-203R
-
UNSPSC31171511
-
Standards/ApprovalsUL Listed
-
Catalog
-
Specification Sheet
Recently Viewed
Dodge® 069412 Imperial Pillow Block Roller Bearing Unit, 2-3/16 in Dia Bore, 6.56 to 6.94 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8.88 in OAL x 5 in OAH
Dodge® imperial spherical roller bearings are the only high-capacity double-row spherical roller bearings with an effective easy-on, easy-off adapter mounting and removal system. Not only does this patented system provide a concentric grip for superior holding on the shaft, but it reduces the fretting corrosion caused by traditional setscrews and vibration.
Weiler® 15131 Small Diameter Wheel Brush, 1-3/8 in Dia Brush, 1/4 in W Face, 0.006 in Dia Crimped Filament/Wire, 1/4 in Arbor Hole
Weiler® 15131 Small Diameter Wheel Brush, 1-3/8 in Dia Brush, 1/4 in W Face, 0.006 in Dia Crimped Filament/Wire, 1/4 in Arbor Hole
Dichtomatik N70013 O-Ring, 013 Dash Number, 0.426 in ID x 0.566 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Dichtomatik N70105 O-Ring, 105 Dash Number, 0.143 in ID x 0.349 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
MORSE® 50414 5330 Jobber Length Drill Bit, 5/16 in Drill - Fraction, 0.3125 in Drill - Decimal Inch, 118 deg Point, Bright
1-15/16" -ID SPHERICAL INSERT BEARING-FAFG1115KRRB >
