MORSE® 59510 5970 Premium Indexable Threading Toolholder, Flat End, Cylindrical Head, 7/16 in Dia Head, 1 in L of Cut, 2-3/16 in OAL, Double Cut
MORSE® 59510 5970 Premium Indexable Threading Toolholder, Flat End, Cylindrical Head, 7/16 in Dia Head, 1 in L of Cut, 2-3/16 in OAL, Double Cut
-
BrandMORSE®
-
UPC686125595104
-
Manufacturer Part Number59510
-
CountryUSA
-
Maximum Speed37000 rpm
-
TypePremium
-
Head CoatingBright
-
Head Diameter7/16 in
-
Head MaterialSolid Carbide
-
Head ShapeCylindrical
-
Applicable MaterialsCast Iron, Ferrous Metals and Steel
-
Series5970
-
Cut TypeDouble
-
Shank Diameter1/4 in
-
Included Angle45 deg
-
Industry SpecificationSA-4
-
End TypeFlat
-
Length of Cut1 in
-
Overall Length2-3/16 in
- Design reduces the pulling action, reduces size of chips
-
UNSPSC23251706
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product contains a chemical known to the State of California to cause cancer or Birth defects. For more information go to www.P65Warnings.ca.gov
-
Catalog
Recently Viewed
MORSE® 59510 5970 Premium Indexable Threading Toolholder, Flat End, Cylindrical Head, 7/16 in Dia Head, 1 in L of Cut, 2-3/16 in OAL, Double Cut
MORSE® 59510 5970 Premium Indexable Threading Toolholder, Flat End, Cylindrical Head, 7/16 in Dia Head, 1 in L of Cut, 2-3/16 in OAL, Double Cut
Drillco 1308A116 1308 Imperial Extra Length Drill, 1/4 in Drill - Fraction, 0.25 in Drill - Decimal Inch, 8 in OAL, HSS
For deep hole drilling. 8" overall length. These drills are made with a general purpose flute design which will perform well under the widest range of operating conditions and materials. Long flutes allow better chip evacuation in deeper holes.
OIL RESISTANT, ANTISTATIC, MAXIMUM BELT LINEAR SPEED UP TO 30M/SEC, INDUSTRIAL BELT TYPE, PRIMARILY USED AS REPLACEMENT ON INDUSTRIAL DRIVES. THE CLASSICAL BELTS ARE RECOMMENDED IN SPECIAL APPLICATIONS SUCH V-FLAT DRIVES. IN THE SAME MANNER THESE BELTS ARE ADVANTAGES WHERE REVERSE IDLERS HAVE TO BE USED BECAUSE OF SMALLER HEIGHTS.
-PIXA116K>
DeWALT® DW5416 Masonry Drill Bit, 1/4 in Drill Bit, 1/4 in SDS-Plus Shank, 2 in D Cutting, Carbide Cutting Edge, 4 in OAL
DeWALT® DW5416 Masonry Drill Bit, 1/4 in Drill Bit, 1/4 in SDS-Plus® Shank, 2 in D Cutting, Carbide Cutting Edge, 4 in OAL
Browning® Classical Gripbelt® 1025907 AK Series Type 1 Single Groove Sheave, Finished Bore, 1/2 in Dia Bore, 2.2 in OD, 2.2 in (A)/1.66 in (3L) Dia Pitch, 21/32 in W Face
Campbell® PD0725027 System 3 Proof Coil Chain, 3/16 in Trade, 30 Grade, 100 ft L, 800 lb Load
Campbell® can trace its beginnings back to 1834, when one of the many companies that eventually became what is today the Campbell® brand began manufacturing harnesses for horses. Over the years, countless products were added, including wire rope and chain fittings, drop forged chain hardware, high quality tackle blocks, shackles, hooks and much more.
