MAK-A-KEY SK08-1 Type 1 Imperial Step Keystock, 5/32 in H x 5/16 in W Base, 3/16 in H x 3/8 in W Step, Carbon Steel
MAK-A-KEY SK08-1 Type 1 Imperial Step Keystock, 5/32 in H x 5/16 in W Base, 3/16 in H x 3/8 in W Step, Carbon Steel
-
BrandMAK-A-KEY
-
Manufacturer Part NumberSK08-1
-
CountryUSA
-
FinishZinc Clear
-
MaterialCarbon Steel
-
TypeType 1 Imperial
-
Base Height5/32 in
-
Base Width5/16 in
-
Step Height3/16 in
-
Step Width3/8 in
-
Length1 ft
-
StyleStep
- Step key stock is used when worn or damaged key ways have been repaired
-
UNSPSC31163208
-
Package Description1/PK
-
Standards/ApprovalsRoHS Compliant|PROP65: This product can potentially expose you to chemicals including lead, nickel and chromium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
-
Catalog
Recently Viewed
MAK-A-KEY SK08-1 Type 1 Imperial Step Keystock, 5/32 in H x 5/16 in W Base, 3/16 in H x 3/8 in W Step, Carbon Steel
MAK-A-KEY SK08-1 Type 1 Imperial Step Keystock, 5/32 in H x 5/16 in W Base, 3/16 in H x 3/8 in W Step, Carbon Steel
Hougen® Rotabroach® 12116 12000 Annular Cutter, 1/2 in Dia Cutter, 1 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
MORSE® 59608 5970 Premium Carbide Burr, Radius End, Taper Head, 1/2 in Dia Head, 1-1/8 in L of Cut, 2-7/8 in OAL, Double Cut
MORSE® 59608 5970 Premium Carbide Burr, Radius End, Taper Head, 1/2 in Dia Head, 1-1/8 in L of Cut, 2-7/8 in OAL, Double Cut
MORSE® 10596 1314 General Purpose Taper Length Drill, 23/32 in Drill - Fraction, 0.7188 in Drill - Decimal Inch, 9-1/2 in OAL, HSS, Black Oxide
MORSE® 10596 1314 General Purpose Taper Length Drill, 23/32 in Drill - Fraction, 0.7188 in Drill - Decimal Inch, 9-1/2 in OAL, HSS, Black Oxide
MORSE® 11372 1340 General Purpose Jobber Length Drill Bit, #61 Drill - Wire, 0.039 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
MORSE® 11372 1340 General Purpose Jobber Length Drill Bit, #61 Drill - Wire, 0.039 in Drill - Decimal Inch, 118 deg Point, HSS, Black Oxide
2-GROOVE 1"-ID A-BELT SHEAVE - IDC2AK0251>
