TIMING BELT SHEAVES
24 TOOTH H-PITCH TIMING BELT SHEAVES
24 TOOTH 8-MM-PITCH TIMING BELT SHEAVES
24-TOOTH H-PITCH MPB TIMING BELT SHEAVE - BRW24HB150>
22 TOOTH H-PITCH TAPER-LOCK TIMING BELT SHEAVES
22 TOOTH H-PITCH SD-BUSH TIMING BELT SHEAVES
22 TOOTH H-PITCH 1.5" WIDE BUSHED GEARBELT SPROCKET, USES P1 BUSHING-BRW22HP150 >
Synchronous Pulley; 1-1/2" Belt Width; 1/2 Inch Belt Pitch; H Belt Style; 22 Teeth; 1-13/16" Face Width; Bushed; 3-13/16" Flange OD; 3.447" Outside Diameter; 3.501" Pitch Diameter; Keyway; 3/8 To 1-1/2" Bushing Bore Range; H Bushing; No Minimum Plain Bore
22 TOOTH H-PITCH 1-1/2" WIDE MINIMUM PLAIN BORE GEARBELT SPROCKET-BRW22HB150 >
TIMING BELT SHEAVE-BRW21XLB037X1/2RWK>
21 TOOTH H-PITCH TIMING BELT SHEAVES
20 TOOTH H-PITCH TIMING BELT SHEAVES
20 TOOTH H-PITCH TIMING BELT SHEAVES
20 TOOTH L-PITCH MINIMUM PLAIN BORE TIMING BELT SHEAVES-BRW20LB050 >
20 TOOTH H-PITCH H-BUSH TIMING BELT SHEAVES-BRW20HH150 >
19 TOOTH L-PITCH MINIMUM PLAIN BORE TIMING BELT SHEAVES-BRW19LB100 >
Split Taper Bushed Timing Belt Pulley, Requires H Bushing
Timing Belt Pulley
1/2 in Belt Pitch
H Belt Size
18 Tooth
1 1/2 in Belt Width
17 TOOTH L-PITCH TIMING BELT SHEAVES-BRW17LF100X3/4 >
17 TOOTH L-PITCH TIMING BELT SHEAVES-BRW17LF075X5/8 >
17 TOOTH L-PITCH TIMING BELT SHEAVES-BRW17LF050X1/2 >
15 TOOTH L-PITCH TIMING BELT SHEAVES-BRW16LF100X5/8 >
16 TOOTH L-PITCH TIMING BELT SHEAVES-BRW16LF075X5/8 >
16 TOOTH L-PITCH TIMING BELT SHEAVES-BRW16LF075X3/4 >
16 TOOTH L-PITCH TIMING BELT SHEAVES-BRW16LF075X1/2 >
16 TOOTH L-PITCH TIMING BELT SHEAVES-BRW16LF050X5/8 >
Recently Viewed
RIDGID® 32910 Screw Feed Tubing Cutter, 1/8 to 1 in Nominal, Ergonomic Grip Handle
The RIDGID Model 10 Screw Feed Tubing Cutter is designed to make clean and smooth cuts on 1/8 to 1-inch diameter copper, brass, aluminum and thin-wall steel.
Browning® 1069533 Split Taper Bushing, 1-3/4 in Dia Bore, 1.8555 in Small End/1.9375 in Large End Dia Barrel, 3 in Dia Flange, 1-15/16 in OAL, Sintered Steel
External key provides positive drive with no torque on the cap screws. We offer high torque carrying capacity. Double split barrel improves true concentricity. The shaft is gripped with positive clamp fit.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
