TIMING BELT SHEAVES
21 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP21H100 >
20 TOOTHXL-PITCH TIMING BELT SHEAVES-IDCP20XL037A >
20 TOOTHXL-PITCH TIMING BELT SHEAVES-IDCP20XL037 >
20 TOOTH L-PITCH MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP20L100 >
20 TOOTH L-PITCH TIMING BELT SHEAVES-IDCP20L075 >
20 TOOTH L-PITCH TIMING BELT SHEAVES-IDCP20L050 >
20 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP20H300 >
20 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP20H150 >
18 TOOTHXL-PITCH TIMING BELT SHEAVES-IDCP18XL037A >
18 TOOTHXL-PITCH TIMING BELT SHEAVES-IDCP18XL037 >
18 TOOTH L-PITCH TIMING BELT SHEAVES-IDCP18L100 >
18 TOOTH L-PITCH TIMING BELT SHEAVES-IDCP18L075 >
18 TOOTH L-PITCH TIMING BELT SHEAVES-IDCP18L050 >
18 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP18H300 >
18 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP18H200 >
18 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP18H150 >
18 TOOTH H-PITCH TIMING BELT SHEAVES-IDCP18H100 >
16 TOOTH H-PITCH 3/4" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP16H300 >
16 TOOTH H-PITCH 3/4" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP16H200 >
16 TOOTH H-PITCH 3/4" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP16H150 >
16 TOOTH H-PITCH 5/8" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP16H100 >
14 TOOTH H-PITCH 3/4" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP14H200 >
14 TOOTH H-PITCH 3/4" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP14H150 >
14 TOOTH H-PITCH 5/8" MINIMUM PLAIN BORE TIMING BELT SHEAVES-IDCP14H100 >
Recently Viewed
Irwin® Record® 2026303 Bench Vise, 4 in Jaw Opening, 4-1/2 in W Steel Jaw, 2-3/8 in D Throat
Irwin® Record® vises are built to handle any job. The impressive, versatile line of vises from Irwin® is designed with the most sought-after features to fit every application, from the garage workbench to the factory floor. Whether used for cutting, screwing, drilling, planning, sanding or just holding, there is an Irwin® Record® vise that's perfect for the any type of holding application. Designed and manufactured to the highest standards and built with the best available materials, Irwin® Record® vises are available in a variety of styles, jaw widths, jaw capacities, base types and clamping forces. Refer to the chart below to select the best vise for the job.
96 CARPENTRY/CONSTRUCTION LEVEL-M-D63412 >
Crosby® 1013904 S-341-1-3/8, Pear Shaped Weldless Sling Link, 3/8 in Trade, 1800 lb Load, Forged Carbon Steel, Self-Colored
Crosby® 1013904 S-341 Pear Shaped Weldless Sling Link, 3/8 in Trade, 1800 lb Load, Forged Carbon Steel, Self-Colored
Gator® GatorGrit 3312 Coated Sanding Sheet, 11-1/4 in L x 4-1/4 in W, 150 Grit, Silicon Carbide Abrasive, Paper Backing
Gator® GatorGrit 3312 Coated Sanding Sheet, 11-1/4 in L x 4-1/4 in W, 150 Grit, Silicon Carbide Abrasive, Paper Backing
Dichtomatik N70435 O-Ring, 435 Dash Number, 5.725 in ID x 6.275 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Sealmaster® two and three piece rod end bearing housing designs have been optimized for overall strength. This housing advantage and variety of outer race materials including brass, steel, DELRIN and PTFE liners provide a wide selection of application solutions. Sealmaster® rod end bearings can be joined together or connected with a threaded rod or tube as linkage assemblies for flexibility in motion transfer. In addition Sealmaster® rod end bearings can accommodate angular misalignment to provide ease in assembly and smooth motion transfer in a variety of applications.
