Sharkbite® UR23037 Straight Stop, 1/2 x 3/8 in Nominal, Push-to-Connect x Compression End Style, 125 psi Pressure, Lead-Free DZR Brass Body
Sharkbite® UR23037 Straight Stop, 1/2 x 3/8 in Nominal, Push-to-Connect x Compression End Style, 125 psi Pressure, Lead-Free DZR Brass Body
-
BrandSharkbite®
-
UPC697285071629
-
Manufacturer Part NumberUR23037
-
CountryUSA
-
Temperature Rating160 deg F
-
Pressure Rating125 psi
-
Nominal Size1/2 x 3/8 in
-
Dimensions1.6 in H x 1.1 in W x 2.6 in L
-
Softgoods MaterialEPDM
-
Body MaterialLead-Free DZR Brass
-
End StylePush-to-Connect x Compression
- Fastest way to connect PEX, copper, CPVC, PE-RT or HDPE SDR-9 pipe
- Can be installed on wet lines and pressure tested immediately
- Stainless steel retainer adds strength and durability
- No special tools, crimping, soldering or glue required
- Can be rotated after installation
- No tube liner required for PEX
-
Standards/ApprovalsASME A112.18.1/CSA B125.1|NSF/ANSI/CAN 61: Q ≤0.5|NSF/ANSI/CAN 372
-
Warranty25 Years
-
Catalog
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Sharkbite® UR23037 Straight Stop, 1/2 x 3/8 in Nominal, Push-to-Connect x Compression End Style, 125 psi Pressure, Lead-Free DZR Brass Body
Sharkbite® UR23037 Straight Stop, 1/2 x 3/8 in Nominal, Push-to-Connect x Compression End Style, 125 psi Pressure, Lead-Free DZR Brass Body
FYH® NAPK209 45MM NAPK Normal Duty Pillow Block Unit, 45 mm Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
FYH® NAPK209 45MM NAPK Normal Duty Pillow Block Unit, 45 mm Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
Sealmaster® 701876 MP Series Medium Duty Pillow Block Ball Bearing Unit, 2-7/16 in Dia Bore, 7-1/8 to 8-7/8 in L Bolt Center-to-Center, 3 in Base to Bore Centerline, 11-1/4 in OAL x 6-1/4 in OAH
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
25-WATT INSIDE FROST BULB #108H&116D-BUL25A >
Proto® J229-01G Needle Nose Plier With Side Cutter and Wire Stripper, Diamond Serrated Steel Jaw, 1-11/16 in L x 1/2 in W Jaw, 5-9/16 in OAL, 9/32 in W Tip
Proto® J229-01G Needle Nose Plier With Side Cutter and Wire Stripper, Diamond Serrated Steel Jaw, 1-11/16 in L x 1/2 in W Jaw, 5-9/16 in OAL, 9/32 in W Tip
9-W 120V MED SCREW BASE FLOOD BULB-BUL24152B>
