NIBCO 1/2" PVC SCH-80 MALE ADAPTERS NIB 836-005
Size: 1/2 inch nominal diameter Material: Gray Schedule 80 Polyvinyl Chloride (PVC)Connection Ends: Socket (Slip) x Male National Pipe Thread (MNPT / MIPT) Pressure Rating Typically up to 150 PSI Max Temperature: 140°F (60°C)
-
BrandLasco®
-
UPC025528720759
-
Manufacturer Part Number836-005
-
CountryUSA
-
Temperature Rating73 deg F
-
MaterialPVC
-
Fitting/Connector TypeAdapter
-
Pressure Rating850 psi
-
Method of ManufactureInjection-Molded
-
ColorGray
-
Schedule RatingSCH 80/XH
-
Nominal Size1/2 in
-
Dimensions1-7/32 in OD
-
Domestic/ImportDomestic
-
Length1-7/8 in
-
End StyleSocket x MNPT
- ASTM D-1784: Rigid poly vinyl chloride (PVC) compounds and chlorinated poly vinyl chloride (CPVC) compounds
- ASTM D-2464: Threaded poly vinyl chloride (PVC) plastic pipe fittings SCH 80/XH
- ASTM D-2467: Socket type poly vinyl chloride (PVC) plastic pipe fittings
- NSF/ANSI standard 61, Annex G: Drinking water system components weighted average lead content of less than or equal to 0.25% and is in compliance with California's health and safety code section 116875 (commonly known as AB1953)
- Do not use Lasco® fittings for compressed air or gases
- Do not test PVC piping systems with compressed air or gases
- Do not use fittings with liquids not recommended by Lasco®
- Fitting modification voids the warranty
-
UNSPSC40171708
-
Package Description25/CTN
-
Standards/ApprovalsASTM D1784|ASTM D2464|ASTM D2467|NSF/ANSI 14|NSF/ANSI 61|Annex-G
-
WarrantyLimited
-
Catalog
-
Specification Sheet
Recently Viewed
Size: 1/2 inch nominal diameter Material: Gray Schedule 80 Polyvinyl Chloride (PVC)Connection Ends: Socket (Slip) x Male National Pipe Thread (MNPT / MIPT) Pressure Rating Typically up to 150 PSI Max Temperature: 140°F (60°C)
3" X 4" GUARD TELFA NON-STICK PAD-OFII261 >
Lasco® 807-005 Elbow, 1/2 in Nominal, Socket x FNPT End Style, SCH 80/XH, PVC, Domestic
Lasco® 848-010 Cap, 1 in Nominal, FNPT End Style, SCH 80/XH, PVC, Domestic
Coilhose® 602 600 Blow Gun, Siphon Spray Tip, 150 psi Working, 8 ft L Tube, 1/4 in FNPT Inlet x 1/8 in FNPT Outlet Thread, Die Cast Zinc, Import
The 600 series blow guns are a thumb lever style blow gun with an ergonomic shape and accept all Coilhose® 1/8 in tips. User comfort was designed into the 600 series with the elimination of the valve where the user's fingers are placed. Models that are designated as "safety" conform to OSHA standards for noise levels (1910.95) and 30 psi dead end pressure (1910.242B).
HCI Preferred Supplier 28652 ST Series Pipe Coupler, 3/8 in Nominal, FNPT, Brass/Buna-N Seal
HCI Preferred Supplier 28652 ST Series Pipe Coupler, 3/8 in Nominal, FNPT, Brass/Buna-N Seal
