Engine Enamels
1-GAL LATEX EXTERIOR GLOSS PASTEL BASE-BLP14165GAL >
1-QT LATEX EXTERIOR GLOSS PASTEL BASE-BLP14165QT >
1-GAL RUS-KIL TINT WHITE BASE-BLP142010GAL >
1-QT RUS-KIL TINT WHITE BASE PAINT-BLP142010QT >
1-GAL DEEP ACCENT BASE PAINT-BLP142030GAL >
1-QT DEEP ACCENT BASE PAINT-BLP142030QT >
1-GAL CLEAR TINT BASE PAINT-BLP142040GAL >
1-QT CLEAR TINT BASE PAINT-BLP142040QT >
1-GAL PASTEL TINT BASE PAINT-BLP14205GAL >
1-QT RUS-KIL PASTEL BASE-BLP14205QT >
STOP STAIN WHITE OIL BASE PRIMER/SEALER SPRAY CAN - BLP1915S >
1-GAL GLOSS WHITE INTERIOR & EXTERIOR PAINT-BLP23BW125GAL >
1-GAL INTERIOR SEMI-GLOSS WALL PAINT-BLP23BW129GAL >
1-GRIT INTERIOR SEMI-GLOSS TINT WHITE BASE-BLP23BW131GAL >
1-GAL INTERIOR SEMI-GLOSS DEEP TINT BASE-BLP23BW139GAL >
1-GAL INTERIOR SEMI-GLOSS CLEAR BASE-BLP23BW140GAL >
1-GAL INTERIOR SEMI-GLOSS PASTEL BASE-BLP23BW141GAL >
2-GAL PAIL INTERIOR & EXTERIOR WHITE PAINT-BLP23DW186 >
1-GAL INTERIOR & EXTERIOR FLAT WHITE PAINT-BLP23DW315GAL >
1-GAL INTERIOR & EXTERIOR WHITE BASE TINT-BLP23DW322GAL >
1-GAL INTERIOR & EXTERIOR CLEAR BASE-BLP23DW328GAL >
1-GAL LATEX EGGSHELL WHITE BASE-BLP233510GAL >
1-QT LATEX EGGSHELL WHITE BASE-BLP233510QT >
1-GRIT LATEX EGGSHELL INTERIOR WHITE PAINT-BLP233517GAL >
Recently Viewed
1-1/8" -IDX1-3/8" -OD VITON O-RING
Browning® 1111814 A Plate Sprocket, 40 Chain, 30 Teeth, For Use With T35L Torque Limiters, 5.06 in OD
Browning® 1111814 A Plate Sprocket, 40 Chain, 30 Teeth, For Use With T35L Torque Limiters, 5.06 in OD
1/4"-OD X .170"-ID BLACK POLYETHYLENE TUBE/TUBING MAXIMUM WORKING PRESSURE AT 75-DEGREES FARENHEIT: 173-PSI WALL THICKNESS: .040" COLOR: BLACK
3/8"-ID X 60" POLYBUTYLENE TUBE-JWH490008
RUS-KIL RUST INHIBITING ALUMINUM SPRAY PAINT-BLP1026S >
Browning® 1296573 T65L Automatic Torque Limiter, 1-7/16 in Finished Bore, 6-1/2 in OD, 4800 in-lb (1-Spring)/8800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
