Quantum® QSB108BK Economy Shelf Bin, 17-7/8 in L x 8-3/8 in W x 4 in H, 0.27 cu-ft, Black
Quantum® QSB108BK Economy Shelf Bin, 17-7/8 in L x 8-3/8 in W x 4 in H, 0.27 cu-ft, Black
-
BrandQuantum®
-
UPC651588028933
-
Manufacturer Part NumberQSB108BK
-
CountryUSA
-
Load Capacity50 lb
-
MaterialInjection Molded Polypropylene
-
ColorBlack
-
TypeEconomy
-
Use Divider NumberDSB108
-
Volume Capacity0.27 cu-ft
-
SeriesQSB108
-
Number of Divider Slots Small7
-
Inside Height4 in
-
Inside Length16-1/2 in
-
Inside Width7-1/8 in
-
Outside Height4 in
-
Outside Length17-7/8 in
-
Outside Width8-3/8 in
- Quantum® tough, durable, high density economy shelf bins are the industry standard for quality
- These durable polypropylene bins feature a molded-in label holder, built-in rear hanglock which allows bins to tilt out for complete access when on shelving
- A wide hopper front allows complete access to the contents of the bin
- Edges are reinforced for added strength
- They are designed for 12 in, 18 in and 24 in deep shelf units, racks or standard shelving
- Bins are impervious to most chemicals
- Bins will last a lifetime and can replace worn out corrugated cardboard bins
-
UNSPSC24112003
-
Package Description10/CT
-
Catalog
Recently Viewed
Quantum® QSB108BK Economy Shelf Bin, 17-7/8 in L x 8-3/8 in W x 4 in H, 0.27 cu-ft, Black
Quantum® QSB108BK Economy Shelf Bin, 17-7/8 in L x 8-3/8 in W x 4 in H, 0.27 cu-ft, Black
Quantum® QSB106YL Economy Shelf Bin, 23-5/8 in L x 6-5/8 in W x 4 in H, 0.28 cu-ft, Yellow
Quantum® QSB106YL Economy Shelf Bin, 23-5/8 in L x 6-5/8 in W x 4 in H, 0.28 cu-ft, Yellow
Quantum® QSB107BL Economy Shelf Bin, 11-5/8 in L x 8-3/8 in W x 4 in H, 0.16 cu-ft, Blue
Quantum® QSB107BL Economy Shelf Bin, 11-5/8 in L x 8-3/8 in W x 4 in H, 0.16 cu-ft, Blue
Quantum® QSB106BK Economy Shelf Bin, 23-5/8 in L x 6-5/8 in W x 4 in H, 0.28 cu-ft, Black
Quantum® QSB106BK Economy Shelf Bin, 23-5/8 in L x 6-5/8 in W x 4 in H, 0.28 cu-ft, Black
8" 3-SQUARE SMOOTH CUT FILE - NIC16102>
Koyo TRB-2435 Double Direction Thrust Washer, 38.1 mm ID x 55.55 mm OD, 1.6 mm W
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
