WERNER 8' 250# TY-1 F/GLS TWIN STEPLADDER WER T-6008
The T6008 fiberglass multi-use twin 8 ft step ladder allows for 250 pounds on either side making these ladders ideal for two person jobs. The high performance dual holstertop has a paint and tool holder adding productivity to the job. Back up aluminum plates reinforce all top connectors and the TRACTION-TRED® steps are slip resistant. The PINCH-PROOF™ spreaders are externally located on the ladder and the EDGE® molded brace and foot pad combination provides enhanced bracing strength and increased protection against damage. Fiberglass rails are non-conductive for working near electricity.
-
BrandWERNER®
-
UPC051751029024
-
Manufacturer Part NumberT6008
-
CountryUSA
-
Load Capacity250 lb
-
MaterialFiberglass
-
TreadRibbed
-
TypeType I
-
SeriesT6000
-
Base Spread64-1/8 in
-
Number of Steps7
-
Ladder Height8 ft
-
Bottom Width25 in
- High performance dual holstertop paint and tool holder
- Back up aluminum plates reinforce all top connectors
- Braces on top steps and bottom three steps
- External PINCH-PROOF™ spreaders
- Slip resistant TRACTION-TRED® steps on front and rear sections
- Rubber step bumpers to resist damage
- EDGE® molded brace/foot pad combination provides enhanced bracing strength and increased protection against damage
- Energy diffusing geometry
- Every rivet backed up by metal, metal plates or washers to protect rails
- Design for one or two person jobs
- Maximum load per side, including person and materials, shall not exceed duty rating of ladder
- Shoulder bolt and nut on top hinge
- 5 ft 9 in H maximum standing
- Medium edge bracing
- 8-1/2 x 13 in top
- 1-1/8 in front and rear flange
- 3 in steps
- Steel spreader
- 3-1/8 in front and rear rail
-
UNSPSC30191501
-
Standards/ApprovalsANSI A14.5 (2007)|OSHA Compliant
Recently Viewed
The T6008 fiberglass multi-use twin 8 ft step ladder allows for 250 pounds on either side making these ladders ideal for two person jobs. The high performance dual holstertop has a paint and tool holder adding productivity to the job. Back up aluminum plates reinforce all top connectors and the TRACTION-TRED® steps are slip resistant. The PINCH-PROOF™ spreaders are externally located on the ladder and the EDGE® molded brace and foot pad combination provides enhanced bracing strength and increased protection against damage. Fiberglass rails are non-conductive for working near electricity.
IKO LRB141816 Inch Series Inner Ring With Oil Groove, 7/8 in ID x 1-1/8 in OD, 25.65 mm OAW, For Use With BR182616 Machined Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
Appleton® UNILETS™ T50A Type T Conduit Outlet Body, 1/2 in Hub, Form 85 Form, 4 cu-in Capacity, Pressure Cast Aluminum, Epoxy Powder Coated
Appleton® Form 85™ UNILETS™ Conduit Outlet Bodies, Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system, they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintece.
FAUCET AERATOR WASHERS WILL FIT MOST AERATOR-JWH413070 >
HellermannTyton T30R3C2 Standard Cable Tie, 5.8 in L x 0.14 in W x 1.1 mm THK, Polyamide 6.6, Orange
Engineered and manufactured for maximum performance and quality.
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric or BOA concentric locking collar. The contact seal with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction.
