2-TON 30'-LIFT HAND CHAIN HOISTS JET101715
JET® S90 Series Hand Chain Hoists were designed with all steel construction and ensure reliability and durability to perform in light-duty industrial applications. Easily maintained and serviced, the JET® S90 is available in capacities from ½ ton to 10 ton and standard lifts of 10, 15, 20, and 30 feet (custom lifts available). The JET® S90 is the ideal contractor grade hoist.
-
BrandJET®
-
UPC731325218947
-
Manufacturer Part NumberJT9-101933
-
CountryUSA
-
Load Capacity2 ton
-
Pull to Lift Rated Load91 lbf
-
TypeContractor Grade
-
SeriesS90
-
Brake TypeDual Pawl Weston
-
Lifting Height30 ft
- Durability, Weston style dual pawl brake system double pawl design increases safety
- Alloy steel hooks industrial rated hooks rotate 360 degrees for easy rigging, hooks slowly stretch to indicate an overload situation increasing jobsite safety
- Heat treated, case hardened and corrosive resistant coated internal parts extend the life of the hoist in the harshest of environments
- Grade 80 black oxide coated load chain for durability
- Impact resistant covers that provide durability and protection
- Needle bearing design promotes long hoist life with low wear reducing downtime
- Smaller body and lightweight design for low headroom applications and use in confined areas
- 71 ft hand chain overhaul to lift load 1ft
- 1 number of fall
- 17-1/2 in headroom
- 8 x 24 mm load chain
-
Alternative Part Number101933
-
UNSPSC24101600
-
Standards/ApprovalsANSI/ASME B30.16 and HST-2 Standards|OSHA Regulations
Recently Viewed
JET® S90 Series Hand Chain Hoists were designed with all steel construction and ensure reliability and durability to perform in light-duty industrial applications. Easily maintained and serviced, the JET® S90 is available in capacities from ½ ton to 10 ton and standard lifts of 10, 15, 20, and 30 feet (custom lifts available). The JET® S90 is the ideal contractor grade hoist.
Our 20 VAC max corded/cordless air inflator can run on any one of three power sources for maximum versatility: 20 VDC max battery, 12 VDC, or 110 VAC. use it on the jobsite, or on the go. It features a high pressure rubber hose for durability. The threaded chuck and included onboard accessories make it easy to inflate items from tires to footballs. Setting desired air pressure is simple with the digital gauge and the auto-shutoff provides accurate inflation. The high volume hose allows fast inflation of mattresses and other inflatables with the push of a button. Move the hose to the deflation port for quick and easy take down. An onboard LED light helps to provide illumination in dark spaces. Heavy duty rubber feet help reduce walking while in use.
NYLON AIR HOSE I.D.--3/8" LENGTH--50' FITTING--3/8" 2-RIGID COLOR--RED
1-1/2 1-1/2" X 1-1/2" X 1-1/4" Galvanized Tee
1-1/2" X 1-1/2" X 1-1/4" GALVANIZED TEE-
Sealmaster 2-15/16"-ID 4-BOLT TRB FLANGE UNIT SEA RFB-215
Sealmaster® RPB mounted tapered roller bearings are a dimensionally interchangeable upgrade from competitive Type E bearings. The exclusive features include unitized replaceable inserts, self aligning capability, split housing and the Sealmaster® alignment pin which provides for a direct path for lubrication into the bearing and helps prevent outer ring rotation. The Sealmaster® RPB is available with two traditional setscrew locking collars for easy installation. The felt seal with flinger provides a good balance between contaminant entry, grease retention and friction. Depending on application requirements, these bearings are available in both inch and metric with a wide variety of housing, sealing and lubrication options.
Dodge® Tigear-2® 26S15L Standard Right Angle Worm Gear Speed Reducer, Separate Input, Solid A Shaft Output, 3.62 hp, 15:1 Gear, 117 rpm Maximum Output, 1708 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
