HCI PREFERRED SUPPLIER
2274 25-blade Metric Feeler Gauge
25-BLADE METRIC FEELER GAUGE SETS-KD-2274>
22822 Oil Seals-2.283" X 2.953" X .315"
OIL SEALS-2.283" X 2.953" X .315"-IMS22822>
22835 Oil Seals-2.281" X 3.154" X .375"
OIL SEALS-2.281" X 3.154" X .375"-IMS22835>
229050 1-oz Eye Wash Solution
1-OZ EYE WASH SOLUTION-CER229050 >
230-2 WILEN 20-OZ RAYON LAYFLAT SCREWTOP MOPS
30" DUSTMOP METAL FRAMES
23002 1/16" X 1/8" Coated Aircraft Cable (ft)
1/16" X 1/8" COATED AIRCRAFT CABLE (FT)-TCI23002 >
23005 2-3/4" URETHANE-FACE HAMMERS
2-3/4" URETHANE-FACE HAMMERS
23006-R 1/8" Red Vinyl Coated Cable 7x19
1/8" RED VINYL COATED CABLE 7X19 TOOTHCI23006R >
2301 RUSTOLEUM PAINT CLEAR U/DOWN MARKING SPRAY PAINT
CLEAR UPSIDE DOWN MARKING SPRAY PAINT-RUS2301 >
23021 2" X 360" 2-ply Twisted-eye Nylon Sling
2" X 360" 2-PLY TWISTED-EYE NYLON SLING - SWC23021 >
23024 Str-ID Spherical Roller Bearing
STR-ID SPHERICAL ROLLER BEARINGS
23026 Str-ID Spherical Roller Bearing
STR-ID SPHERICAL ROLLER BEARINGS
23028 Straight-ID Spherical Roller Bearing
STRAIGHT-ID SPHERICAL ROLLER BEARING-GUL23028 >
23028-K Tpr-ID Spherical Roller Bearing
TPR-ID SPHERICAL ROLLER BEARINGS
23030 Oil Seals-2.313" X 2.997" X .375"
OIL SEALS-2.313" X 2.997" X .375"-IMS23030>
23030 Str-ID Spherical Roller Bearing
Radial shaft seal with metal case and SKF Wave lip, for oil or grease
Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRW1 seals are designed with a metal case, an SKF WAVE lip made of elastomer with higher pumping rate to reduce heat generation, and a garter spring to optimize sealing against the shaft. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
For oil or grease
With garter spring
WAVE lip creates higher pumping rate
WAVE lip has less friction between shaft and lip
WAVE lip has a lower temperature at the contact point
23030-K Tpr-ID Spherical Roller Bearing
TPR-ID SPHERICAL ROLLER BEARINGS
23030-K Tpr-ID Spherical Roller Bearing
Inner Diameter (Bore): 150 mm Outer Diameter: 225 mm Width: 56 mm Bore Type: Tapered (K = taper 1:12) Design Features: Self-aligning, accommodates heavy radial and axial loads in both directions, typically includes an annular lubrication groove with three holes in the outer ring (W33 variant).
230300 Str-ID Spherical Roller Bearing
STR-ID SPHERICAL ROLLER BEARINGS-
Recently Viewed
MORSE® 96130 4550G Center Cutting Regular Length Single End End Mill, 7/8 in Dia Cutter, 1-7/8 in Length of Cut, 4 Flutes, 3/4 in Dia Shank, 4-1/8 in OAL, TiN Coated
MORSE® 43666 1898 Center Cutting Regular Length Single End End Mill, 3/4 in Dia Cutter, 1/5/16 in Length of Cut, 2 Flutes, 3/4 in Dia Shank, 3-9/16 in OAL, Bright
MORSE® 44429 4586 Center Cutting Regular Length Single End End Mill, 5/16 in Dia Cutter, 3/4 in Length of Cut, 4 Flutes, 3/8 in Dia Shank, 2-1/2 in OAL, Bright
MORSE® 44141 4550 Center Cutting Regular Length Single End End Mill, 5/8 in Dia Cutter, 1-5/8 in Length of Cut, 4 Flutes, 5/8 in Dia Shank, 3-3/4 in OAL, Bright
The DCV5801H wet-dry vacuum replacement filter fits DCV580 and DCV581H wet-dry vacuums and traps 99.99% of dust at 1 micron. Wash and reuse filter.
12-PC METRIC MM GEARWRENCH SET-GRW9620>
