Incandescent - Flood Bulbs
7-1/2-SW 7-1/2 Watt 130v Soft White Bulb
7-1/2 WATT 130V SOFT WHITE BULBS
7-W 120V DOUBLE CONTACT CLEAR BULB DC BASE #00023E
75-WATT 130-VOLT INSIDE FROST BULBS-BUL75A130V >
75-WATT 12-VOLT FROSTED BULBS #287C
75-WATT 130-VOLT SAFE-SHIELD BULBS
12624 BULB-GEH75A67WM >
75-WATT CLEAR BULBS #294-G-BUL75ACL >
75-WATT 130-VOLT ROUGH SERVICE BULBS-BUL75ARS >
75-WATT TUFF SKIN BULBS #00353-A
75-WATT FLOODLIGHT BULBS
75-WATT HARD-SHELL FLOODLIGHT BULBS
75-W OUTDOOR FLOODLIGHT BULBS-BUL75PARFL >
75-WATT 120-VOLT REFLECTOR BULBS-BUL75R30SP >
75-WATT BULBS
14.0-VOLT .08-AMP MINIATURE BULBS-BUL756 >
OUTDOOR FLOOD LAMP #02892B-BUL75PAR30QNFLLN30 >
PAR 36" 6-VOLT 8-WATT BULBS #01204A-BUL7613 >
500 WATT BTL 120-V T-6 BULB-BUL7939A>
2-D FLASHLIGHT BULB--CARD OF 2 - JWH800226 >
PR-3 FLASHLIGHT BULBS--CARD OF 2 - JWH800235>
6-V BULB--2 PACK - JWH801680>
7-WATT 120-VOLT BA15D BASE BULBS
90- WATT 130 VOLT CLEAR HALOGEN BULB
90-WATT 130-VOLT SPOTLIGHT 10-DEGREE-BUL90PAR38SP10130V >
Recently Viewed
Dodge® 071128 115 Imperial Type E Pillow Block Roller Bearing Unit, 2 in Dia Bore, 6.88 to 7.12 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8.87 in OAL x 4.47 in OAH
Dodge® imperial spherical roller bearings are the only high-capacity double-row spherical roller bearings with an effective easy-on, easy-off adapter mounting and removal system. Not only does this patented system provide a concentric grip for superior holding on the shaft, but it reduces the fretting corrosion caused by traditional setscrews and vibration.
Drillco 76A108C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 1/8 in Dia Cutter, 3/8 in Length of Cut, 2 Flutes, 1/8 in Dia Shank, 1-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Drillco 76A128C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 7/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 7/16 in Dia Shank, 2-3/4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
Brady® 65666 Small Ball Valve Lockout, Fits Min Pipe Size: 1/4 in, Fits Max Pipe Size: 1 in, 8 Padlocks, -20 deg F Min Temperature, 250 deg F Max
The easy-to-use, single piece design of Ball Valve Lockouts from Brady® makes them the perfect tool for securing your valve handles in the off position.
Power Team 5-TON 1"-STROKE HYD/CYLINDERS RAMS PTD C-51-C
Power Team® C51C C Series General Purpose Spring-Return Single-Acting Hydraulic Cylinder, 5 ton Load, 4.34 in H Min, 5.44 in H Max, 1 in
