HCI Preferred Supplier 96308 Hose Clamp, 5/8 in, 304 Stainless Steel
HCI Preferred Supplier 32308 Elbow, 3/16 x 1/8 in Nominal, Hose Barb x MIP End Style, CA377 Brass
-
BrandGeneric
-
Manufacturer Part Number96308
-
CountryUSA
-
Pipe Size5/8 in
-
Material304 Stainless Steel
-
Cushion MaterialRubber Lined
-
Temperature Rating-40 to 160 deg F
-
Fitting/Connector Type90 deg Elbow
-
Pressure Rating150 psi
-
Method of ManufactureForged
-
Nominal Size3/16 x 1/8 in
-
Dimensions0.95 x 0.7 in
-
Domestic/ImportImport
-
End StyleHose Barb x MIP
- Multiple uses for holding cable, wire, pipe and hose
- Rubber Lined cushion absorbs vibration, provides protection against scratching and is made of black EPDM type rubber
- Bandwidths and mounting hose sizes vary by diameter and material
- Stainless Steel have a 0.20 mm diameter
- Hole Diameter: 0.2 in
-
UNSPSC31162906
-
Package Description100/BG
-
Catalog
Recently Viewed
HCI Preferred Supplier 32308 Elbow, 3/16 x 1/8 in Nominal, Hose Barb x MIP End Style, CA377 Brass
Milwaukee® 8960-20 Cordless Dust Extractor, 12 A, 8 gal Tank, 1.93 hp Power Rating, 120 V
The Milwaukee 8 Gallon dust extractor provides users with an OSHA-compliant solution for the regulation on respirable crystalline silica dust (29 CFR 1926.1153). An automatic filter cleaning mechanism helps maintain consistent airflow and suction at 148 CFM in tough dust-producing applications. The extractor’s two step filtration system includes a HEPA filter, which captures 99.97% of all particles greater than 0.3 microns for best in class filtration and safety. For added convenience, an on-board tool activated plug allows users to start and stop the vacuum with a power tool to increase productivity. The adapters included are compatible with all Milwaukee dust extraction accessories.
HEAVY DUTY CONTRACTOR BAGS WITH FLAP TIE OR TWIST TIE FOR EASY CLOSURE. SUITABLE FOR PROFESSIONAL AND RESIDENTIAL USE. CONSTRUCTED OF STRONG, THICK PLASTIC.
JWH647926 >
48X75" WATER HEATER JACKET FOR ELECTRIC OR GAS WATER HEATERS. VINYL COVERED FIBERGLASS MATERIAL WITH TAPE AND INSTRUCTIONS INCLUDED-JWH426863 >
PE3103 by Coilhose | Tubing | 5/16" OD x .236" ID | .038" Wall thickness | Natural | Polyethylene
Browning® 1296482 T55L Automatic Torque Limiter, 1 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
