Klein® D333-8 Conduit Locknut and Reaming Plier, Knurled Tool Steel Jaw, 1-5/8 in L x 0.938 in W Jaw, 7-3/4 in OAL, 3/16 in W Tip
The Conduit Locknut and Reaming Pliers tighten up to 3/4-inch EMT and 1/2-inch rigid locknuts. The special jaw is designed for locknuts, conduit and caps. Serrated jaws deburr the outside while the nose reams and smooths the inside of conduit up to 3/4-inch EMT. The long-nose design makes it easier to reach into electrical boxes.
-
BrandKlein®
-
UPC092644712593
-
Manufacturer Part NumberD333-8
-
CountryUSA|Canada
-
Tip Width3/16 in
-
ColorYellow
-
TypeConduit
-
Handle MaterialPlastic
-
Non-SparkingNo
-
Jaw Length1-5/8 in
-
Jaw MaterialTool Steel
-
Jaw Opening1-1/2 in
-
Jaw TypeKnurled
-
Jaw Width0.938 in
-
Overall Length7-3/4 in
- Pliers tighten 1/2 in (13 mm) and 3/4 in (19 mm) EMT or 1/2 in (13 mm) rigid locknuts
- Fits liquid tight fittings and caps
- Reams and deburrs both inside and outside of conduit
- Knurled jaws at nose tip pull wire or fish tape and machined nose fits snugly into locknut wings
- Forged in the USA with custom, US-made tool steel for maximum durability
| Competitor Name | Competitor Part Number |
|---|---|
| Grainger | 2DHA6 |
| MSC | 00341792 |
-
Alternative Part Number8520828
-
UNSPSC27112134
-
IDEA Index ID8520828
-
Package DescriptionEACH
-
Standards/ApprovalsPROP65: Cancer and reproductive harm - See www.P65Warnings.ca.gov for more information
-
Specification Sheet
Recently Viewed
Klein® D333-8 Conduit Locknut and Reaming Plier, Knurled Tool Steel Jaw, 1-5/8 in L x 0.938 in W Jaw, 7-3/4 in OAL, 3/16 in W Tip
The Conduit Locknut and Reaming Pliers tighten up to 3/4-inch EMT and 1/2-inch rigid locknuts. The special jaw is designed for locknuts, conduit and caps. Serrated jaws deburr the outside while the nose reams and smooths the inside of conduit up to 3/4-inch EMT. The long-nose design makes it easier to reach into electrical boxes.
FYH® UCP210 50MM UCP Normal Duty Pillow Block Unit, 50 mm Dia Bore, 6-1/4 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8-1/8 in OAL 4-7/16 in OAH
FYH® UCP210 50MM UCP Normal Duty Pillow Block Unit, 50 mm Dia Bore, 6-1/4 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8-1/8 in OAL 4-7/16 in OAH
FYH® UCP210-31 Pillow Block Unit, 1-15/16 in Dia Bore, 6-1/4 in L Bolt Center-to-Center
FYH® UCP210-31 Pillow Block Unit, 1-15/16 in Dia Bore, 6-1/4 in L Bolt Center-to-Center
Sealmaster® 700596 NPL Standard-Duty Pillow Block Ball Bearing Unit, 2-7/16 in Dia Bore, 6-7/8 to 7-5/8 in L Bolt Center-to-Center, 2-11/16 in Base to Bore Centerline, 9-1/2 in OAL x 5-1/2 in OAH
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
PROJECTOR BULBS-BULCVJ>
Permatex® 80008 Form-A-Gasket® #1 No.1 Fast Dry Rigid Cure Gasket Sealant, 3 oz Container Tube Container
Permatex® Form-A-Gasket® No. 1 Sealant is a reddish brown, viscous paste with a characteristic alcoholic odor. It is a fast drying paste that changes to a hard, semi flexible seal through solvent evaporation. It seals flanges, fittings, connections and assembles against leakage. Improves gasket seal in permanent and rigid assemblies.
